manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

562

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Settings

Identification
Switching the DHCP Client On/Off

Identification

The PBX is integrated into an existing network. To make sure the PBX can be identified in this 
network, several settings must be configured.

Switching the DHCP Client On/Off

If the DHCP client function has been enabled, the PBX automatically receives its IP address 
from an DHCP server.

Proceed as follows:

•

Using the configuration manager

•

Using a character string on the internal telephone (see section Short Reference)

1. Open the page 

Administration > IP configuration

.

2. Select or clear the 

Receive the IP address automatically (DHCP client)

 check box 

under 

ETHERNET CONFIGURATION

.

Configuring the IPv4 Address of the PBX

Proceed as follows:

•

Using the configuration manager

•

Using a character string on the internal telephone (see section Short Reference)

Requirements:

•

Disabled DHCP client

1. Open the page 

Administration > IP configuration

.

2. In the 

IP address

 entry field under 

ETHERNET CONFIGURATION

, enter the IPv4 

address of the PBX. Possible entries:

IP address with a range of 0 to 255 (example: 192.168.0.240)

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Panasonic KX-TDE100 Configuration Manual preview
KX-TDE100
Brand: Panasonic Pages: 13
Panasonic KX-NS300 Pc Programming Manual preview
KX-NS300
Brand: Panasonic Pages: 752
Panasonic KX-NS300 Installation Manual preview
KX-NS300
Brand: Panasonic Pages: 300
Panasonic KX-TDA100D User Manual preview
KX-TDA100D
Brand: Panasonic Pages: 240
Panasonic KX-NS500 Sales Manual preview
KX-NS500
Brand: Panasonic Pages: 92
Panasonic KX-NS500 Features Manual preview
KX-NS500
Brand: Panasonic Pages: 580
ATCOM IPPBX IP4G User Manual preview
IPPBX IP4G
Brand: ATCOM Pages: 68
Quadro Quadro2x Installation Manual preview
Quadro2x
Brand: Quadro Pages: 57
Panasonic KX-NS500AG Service Manual preview
KX-NS500AG
Brand: Panasonic Pages: 191
ATL Berkshire 10K ipPBX Quick Start Manual preview
Berkshire 10K ipPBX
Brand: ATL Pages: 42

Brands by name

Popular brands

Load more brands