manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

537

Functions

VoIP/GSM Routing

Configuring Configuration Dependent VoIP/GSM Routing

1. Open the page 

Routing > VoIP and GSM routing > Exception numbers

.

2. Click   

Export

.

The dialogue for downloading the text file ausnahmerufnr.csv appears.

3. Save the text file on the PC.

Configuring Configuration Dependent VoIP/GSM Routing

In case that the selected provider has low prices only for a limited space of time, you can switch 
on and off single exception numbers by configuration.

Proceed as follows:

•

Separately for configurations

•

Using the configuration manager

Requirements:

•

Configured exception numbers

1. Open the page 

Routing > VoIP and GSM Routing > Routing is configuration 

dependent

.

2. Select or clear one or several check boxes under 

Configurations

 to assign single 

configurations to an exception number or select the check box under 

For all config-

urations

 to assign all configurations to an exception number.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Yeastar Technology K2 VoIP PBX Hardware Installation Manual preview
K2 VoIP PBX
Brand: Yeastar Technology Pages: 10
Orchid PBX 308 System Administrator Manual preview
PBX 308
Brand: Orchid Pages: 20

Brands by name

Popular brands

Load more brands