manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

490

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Call Forwarding
Switching Group Call Forwarding Only for External Calls On/Off

The group property 

Call Restrictor settings of the subscribers

 functions 

like 

No Call Restrictor

 for call forwarding for groups.

The group property 

Call Deblocker settings of the subscribers

 functions 

like 

No Call Deblocker

 for call forwarding for groups.

The group property 

Exchange line authorisation of the subscribers

 

functions like 

International

 for call forwarding for groups.

The group property 

Telephone book authorisation of subscribers

 

functions like 

Telephone book authorisation of all group members

 like for 

call forwarding for groups.

Preferred exchange line/Number Presentation: The number of the group is 
always presented.

To avoid having to use a second call channel in the case of call forwarding to 
an external destination, the PBX tries to reroute the call directly at the 
network provider using call deflection. The following requirements must be 
fulfilled for this purpose: 1. The incoming call was made via an ISDN network 
provider supporting call deflection. 2. The rerouted phone number is neither 
called as a group member, nor is it required to consider parallel calling or 
fallback on busy.

Switching Group Call Forwarding Only for External Calls On/Off

If call forwarding for groups (unconditional, on busy, on no reply) is only performed for external 
calls,only external calls will be forwarded.

Proceed as follows:

•

Separately for groups

•

Separately for configurations

•

Using the configuration manager

Note:

 As described in the following, the setting is also possible via profiles (

... 

> Profiles > Configuration > Configure > ...

). If the check box 

Profile-

controlled settings

 has been selected, the property set in the right-hand 

column will apply. For assignment of the profile, see chapter Settings > 
Profiles.

1. Open the following page:

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Switch Voice BR4 User Manual preview
BR4
Brand: Switch Voice Pages: 48
Panasonic KX-NS700 Feature Manual preview
KX-NS700
Brand: Panasonic Pages: 580
Panasonic KX-NS500 Getting Started preview
KX-NS500
Brand: Panasonic Pages: 62

Brands by name

Popular brands

Load more brands