Auerswald COMpact 5000 Operation Manual Download Page 428 | Manualshive

Page: 428 / 932

background image

428

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

Functions

Online Name Search
Creating Default Service Providers Automatically

Requirements:

•

A configured DNS server and, if necessary, an HTTP proxy server (

Administration > IP

configuration

)

•

A configured gateway

•

The name of at least one online service provider must have been entered for the online
name search

1. Open the page

Functions > Online name search > Basic settings

.

2. Select or clear the

Online name search

check box.

3. If you have enabled online name search, click the options field In the

Active

column

in the line of the service provider to be used for the online name search.

Creating Default Service Providers Automatically

The service provider list accommodates up to five service providers.

Proceed as follows:

•

Using the configuration manager

1. Open the page

Functions > Online name search > Basic settings

.

2. Click

Standard

.

3. Click

Continue

.

The data of the service providers is added to the existing list of providers, without
verification whether a provider is already contained in the list (double entries).

Note:

When creating default values for providers, the import is only carried

out until the maximum number of providers is reached and then it is
cancelled.

«
...
426
427
428
429
430
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: Panasonic Pages: 892

Brand: Matrix Pages: 18

EPABX Vision-206S

Brand: Matrix Pages: 235

Brand: MCK Pages: 24

EXTender PBXgateway II

Brand: MCK Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands