manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

333

Functions

Busy-on-Busy

Switching Busy-on-Busy On/Off

Busy-on-Busy

With help of the Busy-on-Busy function, it is possible to define the maximum active call connec-
tions for one group (in single increments until the maximum number of possible external call 
channels minus two). If this number has been reached, all additional callers hear the busy 
signal. However, members of the group may make additional calls (outgoing calls) if there are 
still external call channels available.

Switching Busy-on-Busy On/Off

If Busy-on-Busy is enabled, the number of callers put into the waiting loop automatically is 
limited.

Proceed as follows:

•

Separately for groups

•

Separately for configurations

•

Using the configuration manager

Note:

 As described in the following, the setting is also possible via profiles (

... 

> Profiles > Configuration > Configure > ...

). If the check box 

Profile-

controlled settings

 has been selected, the property set in the right-hand 

column will apply. For assignment of the profile, see chapter Settings > 
Profiles.

1. Open the page 

Groups > Properties > Reachability

.

2. In the list field at the top, select the group in question by its name or number.

3. In the 

Busy-on-Busy

 list field, select one of the following options:

Note:

 

The setting 

busy from 1 connection on

 makes sense if e. g. the group is 

used to call one user on several telephones.

disabled

: Disables busy on busy.

busy from x connections on

: The number of callers put into the waiting loop 

automatically is limited to the number configured here.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Yeastar Technology MyPBX Standard User Manual preview
MyPBX Standard
Brand: Yeastar Technology Pages: 152
Karel MS48IP Programming Manual preview
MS48IP
Brand: Karel Pages: 96
Panasonic KX-TDA200AL Brochure & Specs preview
KX-TDA200AL
Brand: Panasonic Pages: 16
Panasonic KX-TDA600 - Hybrid IP PBX Control Unit Max. 1008... Installation Manual preview
KX-TDA600 - Hybrid IP PBX Control Unit Max. 1008...
Brand: Panasonic Pages: 232

Brands by name

Popular brands

Load more brands