manualshive.com logo in svg

Auerswald COMpact 5000, Operation Manual

The comprehensive Instructions Manual for the high-performance Auerswald COMpact 5000 is available for free download at manualshive.com. This manual provides a detailed guide on how to maximize the functionality of this exceptional product, ensuring seamless integration and optimal performance for your business communication needs.

Share
Download
background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

325

Functions

Automatic Reception

Automatic Reception Management

–

Using the Configuration Manager (page 

Public switched tel. networks > Call distri-

bution

)

Automatic Reception Management

Proceed as follows:

•

Using the Configuration Manager (page 

Functions > Automatic Receptions

)

Requirements:

•

Enabled automatic reception function (optional, see Important Information > Product Details 
> Basic Assembly and Extensions section)

Internal phone number of the reception

 

This (exchange line access number) is an internal number. You can select any of the numbers 
in the internal supply of phone numbers. This number is then used for distributing calls and can 
be called directly by an internal subscriber.

Notes:

A number cannot be allocated twice.

Using numbers with few digits (two- or three-digit numbers) inevitably 
restricts the possible supply of numbers that require more digits. For 
example, if the phone number 12 is assigned, the phone numbers 120 to 129 
and 1200 to 1299 are no longer available.

The default exchange line access number on the PBX is 0 in the factory 
settings. However, this can be changed. Note that changing the exchange 
line access number restricts the telephone numbering plan.

Name

 

Freely selectable name. This name is used to identify the automatic reception within the PBX.

New

Adds a new automatic reception. You must then make the settings for this new automatic 
reception.

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Nokia 22 Operator'S Manual preview
22
Brand: Nokia Pages: 54
Yeastar Technology N824 User Manual preview
N824
Brand: Yeastar Technology Pages: 104
Panasonic KX-TDA100AL Service Manual preview
KX-TDA100AL
Brand: Panasonic Pages: 125
Miracall Technology IP PBX MC-IP8008 User Manual preview
IP PBX MC-IP8008
Brand: Miracall Technology Pages: 32

Brands by name

Popular brands

Load more brands