Auerswald COMpact 5000 Operation Manual Download | Manualshive

Page: 125 / 932

background image

COMpact 5000/R - Firmware V6.6A - Installation, Operation and Configuration V05 03/2016

125

Introduction to the Configuration Manager

Configuration Manager

Configuration Wizard

Note:

IPv6 address cannot be entered using the configuration wizard.

You can make further settings under

Administration > IP configuration

.

For further information, click

or one of the help topics.

Port Configuration

The page

Port configuration

is only visible in the configuration wizard if a COMpact 2BRI

module is plugged in and at least one port is configured for the operating mode

ISDN external

.

An external S

0

port can be used for the following types of connections:

• PTMP connection

: ISDN PTMP connection with up to ten multiple subscriber numbers

(MSNs).

• PTP connection

: ISDN PTP connection with PBX base number and Direct Dial In numbers

(DDI numbers).

You can make further settings under

Hardware > Port configuration

.

For more information, click one of the help topics.

Basic Settings

For some of its functions (e. g. Call Through, call restrictors, call deblockers), the PBX needs
the prefixes of its location.

The exchange line access number is needed to request an external line (exception: Direct
Exchange Line Telephone).

You can make further settings under

Public switched tel. networks > Exchange line

request

.

For further information, click

or one of the help topicx.

Public Switched Telephone Networks

The configuration wizard allows you to configure the PBX for four different types of connec-
tions. Which connection type is offered for selection depends on the plugged in module type.

«
...
123
124
125
126
127
...
»

Summary of Contents for COMpact 5000





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for COMpact 5000

Brand: D-Link Pages: 52

Brand: Well Pages: 8

Brand: Well Pages: 13

Brand: Yeastar Technology Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands