Auerswald COMfortel 1100 Operation And Configuration Instructions Download Page 189 | Manualshive

Page: 189 / 273

Auerswald COMfortel 1100 Operation And Configuration Instructions Download Page 189

COMfortel 1100 - Firmware Version 4.4 - COMfortel Set V2.7 - Version of the Manual 04 11/10

189

Configuring and Operating Functions
Power Save Mode
Switching Automatic Activation of Power Save Mode On/Off

Power Save Mode

In power save mode, the LEDs are inactive (exception: the message LED blinks for missed
calls).

After a configurable waiting time and depending on the configuration, power save mode can be
activated automatically during the switchover into a PBX configuration and/or manually by
pressing a key. Power save mode is deactivated again as soon as an incoming call is signalled
or any key is pressed.

Switching Automatic Activation of Power Save Mode On/Off

If automatic activation of power save mode is enabled, the telephone automatically switches
into power save mode when the telephone is not in use.

The holding time indicates how much time after the key was last pressed before power save
mode is activated.

Switching this on/off can be done as follows:

• Via COMfortel Set

Switching Automated Activation of Power Save Mode On/Off via COMfortel Set

Requirements:
– An open configuration and the required PIN, if necessary

1.

Open the page Settings/functions > Power save mode.

2.

Select or clear the Automated activation check box.

3.

Enter a value in the corresponding Waiting time (1 to 999 minutes) entry field. The
following entries are possible:

Further steps:
– Save your configuration before closing.

Enables the automated activation of power save mode.

Disables the automated activation of power save mode.

1 to 999: After 1 to 999 minutes, power save mode is automatically activated,
depending on the entry.

«
...
187
188
189
190
191
...
»

Summary of Contents for COMfortel 1100


















































































































































































































































































Reviews:

No comments