background image

INSTALLER

 

7 & 11kW HRC

70

 

HIGH TEMPERATURE HEAT PUMP

 

 - 

4

1.1 - Important information

1.2 - Safety instructions and advice

1 -  PLEASE READ 

IMMEDIATELY

These installation and operating instructions form part of the 
appliances which they refer to. 

In order for the warranty 

to be valid, they must be read before using the 
appliance.
This manual must be kept and passed on to 
successive users for future reference. It will be 
considered as evidence in case of litigation.

• The Heat Pump must only be installed outdoors.

• This appliance is not intended for use by people (including 

children) who have reduced physical, sensory or mental 
capacities, or by people who have insuffi

  cient experience or 

knowledge of the product, unless they are being supervised by 
someone who is responsible for their safety and in possession of 
the instructions on how the appliance should be used.

• Installing the Heat Pump indoors is 

strictly forbidden

.

• The Heat Pump has an operating range of -20°C to 40°C. When 

the temperature falls below -20°C, the installation is no longer 
heated by the Heat Pump, but by the back-up.

• It is FORBIDDEN : 

- to let the Heat Pump run using air intake which contains 

solvents or explosive matter

- to use air intake which contains grease, dust or aerosol 

particles

- to connect vented exhaust hoods 

• It is  

FORBIDDEN

 to use the appliances if the installation is not 

fi lled with water

• All work undertaken on the installation must be carried out by 

a qualifi ed professional with the appliances disconnected from 
the mains power supply.

• This appliance must be installed in accordance with national 

electrical installation regulations.

• Check that the installation is equipped with a properly sized and 

connected ground cable.
This CE-approved unit is in compliance with the essential 
requirements of the following directives:

- low voltage 2006/95/CEE (standard EN 60.335.1)

- electromagnetic compatability 2004/108/CEE (standard EN 

55014.1 / EN 55014.2).

• Any work undertaken on the refrigerant circuit must be carried 

out by a qualifi ed professional with a category 1 certifi cate 
of aptitude. It is prohibited to release refrigerant into the 
atmosphere: it is mandatory to recover the refrigerant before 
beginning any work on the circuit.

 

The high temperature Heat Pump absorbs the calories contained 
in outdoor air, transforms them into useful energy and transfers 
them to the heating water for your home. AUER cannot be held 
responsible for any other usage of the appliance.

The safety advice and instructions which are given here must be 
strictly respected.

Before making any connections, make sure that the appliances 
are compatible with the installation.

Before switching the system on, make sure that the network 
voltage to be applied to the appliances is the same as the voltage 
indicated on their rating plates.

Before undertaking any maintenance or handling or in case of the 
appliances functioning incorrectly or not at all, always disconnect 
from the mains power supply and seek advice from a specialist.

AUER declines any responsibility for damage caused by these 
instructions not being followed and any errors due to improper 
handling, installation or usage.

These installation and operating instructions are subject to 
change without prior notice.

- It is the responsibility of the installer and 

the client to contact the electricity provider and 
ensure that the appliance is compatible with 
the power grid before connecting the HRC

70 

Heat Pump (see the information form which is 
an appendix to this document).

- The power grid impedance value must be less 

than the Heat Pump impedance Z

max 

 (see § 

"Connecting the HRC

70  

Heat Pump to the power 

supply").

- If electrical installation standards are not 

respected, irreversible damage could be 
sustained to the HRC

70  

Heat Pump, which will 

not be covered by the manufacturer’s warranty.

ELECTRICAL INSTALLATION 

RECOMMENDATIONS

- Rinse and clean the hydraulic heating 
circuit before connecting the Heat Pump 

and Pilot.
- The appliance only works when fi lled with 

water. Never switch the appliance on if it has not 
been properly purged and fi lled with water.

- The fi lter valve protects the Heat Pump; an 

annual check on the condition of the fi lter must 
be carried out.

- We recommend that you check for sludge 

and limescale from time to time and clean if 
necessary.  The appliance must be switched off  
before any cleaning is undertaken.

- Always switch the appliance off  before working 

on any electrical parts.

  Caution: the fan may still continue to run 

through inertia even when the appliance has 
been switched off .

- Never put water on the control components 
or any electrical parts. Switch off  the appliance 
before cleaning.

HYDRAULIC INSTALLATION 

RECOMMENDATIONS

Summary of Contents for HRC 70 PILOT-PREMIUM













































































Reviews: