manualshive.com logo in svg

Audison bit Tune, User Manual

Share
Download
Audison bit Tune User Manual Download Page 27

USER’S MANUAL / bit Tune /

27

6. BIT TUNE DESKTOP

In order to use the main tools of the 

bit Tune

 you must install the software on your PC 

(see sect. 5)

. The bit Tune must 

be connected to the PC and be turned on by setting the measurement selection 

switch

 in the 

PC analyzer

 position

 

(see sect. 3.3.2)

. Start the software by clicking the icon on your desktop.

The first screen that appears is the starting screen, where you need to select one of the following modes:

-  bit Tune + Processor:

 bit Tune connected and interfaced to a processor 

(see sect. 6.2)

;

-  bit Tune

 

(see sect. 6.3)

;

- Offline:

 bit Tune not connected 

(see sect. 6.1)

;

-  Rescue Mode:

 Firmware upgrade recovery 

(see sect. 9.3)

.

To select the starting mode, go to the drop-down menu, select the appropriate entry and press

 ENTER

 or click on the 

window.

6

Summary of Contents for bit Tune





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands