5
MIXER PROFESSIONALI
Serie
PAMX2
Left
Right
10
10
0
15
20
30
40
60
Bal
or
Unbal
EQ
HIGH
12 KHz
MID
2.5 KHz
LOW
80 Hz
AUX
PRE
FX
PAN
MUTE
CLIP
SOLO
0
+15
- 15
0
+15
- 15
0
+15
- 15
-
¥
0
+ 15
0
-
¥
+ 15
9/10
MUTE
ALT 3-4
MONO
L
R
LEVEL
LINE IN 9/10
+ 4
-10
Fig 2
16
17
STEREO CANNELS
MIXER PROFESSIONALI
Serie
PAMX2
PORTA USB
16.
L channel of a stereo source or a mono signal can be connected
to this 6,3 mm Jack input. Signal can be either balanced or
unbalanced*
17.
Only R channel of a stereo signal can be connected to this 6.3
mm input
3.
This switch sets the channel input level (+ 4 / - 10 dB
attenuation)
5.
EQ HIGH: This control a/- 15 dB with a "shelving" curve
shape
at 12 kHz.
6.
EQ MID: This control adjusts +/- 15 dB with a band center at
2.5 kHz.
7.
EQ LOW: This control adjusts +/- 15 dB with a "shelving" curve
shape at 80 Hz.
8.
AUX:This control adjusts the output signal level
AUX SENDS 1, controlled through general adjustment (18). This
signal is normally "post" FADER but could become "pre" FADER by
operating the button (9)
9.
This button operates the pre/post FADER level of the AUX
control
10.
FX: This control adjusts signal level to send to AUX SENDS 2
and to DSP, controlled through general adjustment (19).This signal is
always "post" FADER
11.
PAN: It adjusts the stereo scene by adjusting the signal levels to
send to right and left outputs.
12.
MUTE: This dual-purpose switch turns off the channel and
sends at the same time a signal to an alternative mixing (ALT 3/4 ).
Function is on when yellow LED lights up.
13.
CLIP: The red LED is dual-purpose too: it indicates "SOLO"
function (See point 14) or indicates CLIPPING mode.
Important: in case LED lights up indicating clipping mode, operate by
reducing the TRIM
14.
SOLO: This button sends the signal to PHONES and CONTROL
ROOM OUT outlets and allows you to hear signals through your
headphones and view signal on LED level indicators. Operating the
"MODE" switch of the main section, it's possible to choose pre or post
FADER signal.
15.
FADER: It adjusts the level of the channel signal.
* See connection scheme on page 7
Audiodesign PRO professional
mixers PAMX2 series, are supplied
with a full speed USB port which you
can connect to a computer and allows
you to exchange CD-quality audio
between mixer and computer; mixer
operates also as and external
soundcard.
Recording on PC can be made using
the computer's built-in audio recorder,
or better, using a dedicated software.
To ensure that the mixer is correctly
recognized by the PC, always turn on
the mixer before inserting USB cable
into the PC.
When turning off, turn off the
computer first until shut down
process is completed and then turn
off the mixer.
Windows automatically recognizes
the mixer at the first connection and
proceed to install necessary drivers,
eventually will require to insert the
Windows CD.
Open the control panel and select
"USB Audio Codec" as default sound
recording and playback device. Also
for Macintosh, the selection of "USB
Audio Codec" is the only action
required.
Better performances can be obtained
using specific Digital Audio
Workstation software, in which case
the specific installation instruction
must be followed.
To use the mixer for playback from
PC, operate buttons and controls 2
TR/USB, for MAIN MIX or
PHONES/CTRL R outputs.
For recording to PC from Mixer while
it's working, start registration on PC's
software and adjust its level from the
MAIN MIX Fader.
SPECIFICATIONS
Section
Level and datas
MONO INPUT CHANNELS
Mic In
Sensitivity from
0 to - 60 dB
XLR-F Balanced
Impedance
2 Kohm
Line In
Jack Balanced
Impedance
10-20 Kohm (Bal-Unbal)
EQ
STEREO INPUT CHANNELS
Line In
Sensitivity from
- 10 a + 4 dB
Impedance 20
Kohm
EQ
HIGH ±15 dB @ 12 KHz shelving
MID
±15 dB @ 2.5 KHz peaking
LOW
±15 dB @ 80 Hz shelving
MASTER SECTION
Nominal Output level + 4 dBu
2-TRK - CD/TAPE
Nominal Output level
0 dBu
Nominal Output level - 10 dBv
HEADPHONES
Min Impedance
32 ohm
Jack Stereo
Max Output
(2x) 193 mW
DIGITAL EFFECT PROCESSOR
Preset
Delay STEREO, MONO e TAP
Modulations CHORUS e FLANGER
Combinations REV + STEREO DELAY, REV + MONO DELAY,
REV +CHORUS e REV + FLANGER
USB INTERFACE
Version
Resolution
Sampling
Rate
MAIN SPECIFICATIONS
Max Level
Crosstalk
Hum and Noise
THD + Noise
Weight
Dimensions (WxDxH)
Connector
XLR / Jack Bal.
Jack
Unbal mono
RCA
Fully compliant with USB 1.1
16-Bit Delta Sigma ADC e DAC
DAC: 32, 44.1, 48 kHz
ADC: 8, 11.025, 16, 22.05, 32, 44.1, 48 kHz
all outputs +22 dBu
meas at 1 KHz
> 82 dB
unweighted
< -93 dBu
a +4dB, 1kHz
< 0,008 %
Reverbs: HALL, ROOM, VOCAL e PLATE
MAIN MIX OUT
C. ROOM output
AUX SENDS 1
AUX SENDS 2
Jack
Unbal mono
Jack
Unbal mono
Jack
Unbalanced
Jack Balanced
Jack
Unbalanced
PAMX 2.62
PAMX 2.102
5.3 Kg
4.0 Kg
34.4 x 35 x 11.2 cm
45 x 35 x 11.2 cm
Nominal Output level + 4 dBu
Nominal Output level + 4 dBu
Nominal Output level + 4 dBu
HIGH ±15 dB @ 12 KHz shelving
MID
±15 dB @ 2.5 KHz peaking
LOW
±15 dB @ 80 Hz shelving
Sensitivity from
- 10 a + 4 dB
8
