3
MIXER PROFESSIONALI
Serie
PAMX2
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
EQ
EQ
EQ
EQ
EQ
EQ
EQ
EQ
MID
MID
MID
MID
MID
MID
MID
MID
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
12 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
2.5 kHz
LOW
LOW
LOW
LOW
LOW
LOW
LOW
LOW
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
80 Hz
PRE
PRE
PRE
PRE
PRE
PRE
PRE
PRE
AUX
AUX
AUX
AUX
AUX
AUX
AUX
AUX
FX
FX
FX
FX
FX
FX
FX
FX
PAN
PAN
PAN
PAN
PAN
PAN
BAL
BAL
3
1
4
2
5
6
7/8
9/10
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
ALT 3-4
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
MUTE
dB
dB
dB
dB
dB
dB
dB
dB
1
2
5
6
9/10
1
1
1
1
1
1
1
1
2
2
1
1
1
2
2
2
2
2
2
2
2
ALT
MAIN MIX
3-4
3
4
L
R
SOLO
SOLO
FX
FX
TO AUX
SEND 1
MAIN MIX
ALT 3-4
AUX SENDS
STEREO AUX RETURNS
PROGRAM
( PUSH )
2-TR/USB
ALT 3-4
MAIN MIX
SOURCE
MAX
2-TR/USB TO MAIN
PHONES/CTRL R
MAIN SOLO PFL
MODE
SOLO (NORMAL)
PFL (LEVEL SET)
10
5
2
0
2
5
20
MIC 3
MIC 1
MIC 4
MIC 2
MIC 5
MIC 6
LINE IN 5/6
LINE IN 7/8
RIGHT
LEFT/ MONO
AUX SENDS
2
1
2
1
FX
INPUT
OUTPUT
CD/TAPE
00 SMALL HALL
03 MID HALL
06 BIG HALL
09 CHURCH
10 SMALL ROOM
13 MID ROOM
16 BIG ROOM
19 CHAPEL
20 SPRING
27 SPRING
30 GATED REV
36 REVERSE
40 EARLY REFL
44 AMBIENCE
48 STADIUM
49 AMBIENCE FX
50 DELAY
59 ECHO
60 CHORUS
66 FLANGER
70 PHASER
74 PITCH SHIFT
80 CHORUS & REVERB
82 FLANGER & REVERB
84 PHASER & REVERB
86 PITCH & REVERB
88 DELAY & REVERB
90 DELAY & GATED
91 DELAY & REVERSE
92 DELAY & CHORUS
94 DELAY & FLANGER
96 DELAY & PHASER
98 DELAY & PITCH
24-BIT MULTI-FX PROCESSOR
ULTRALOW-NOISE DESIGN
14-INPUT 2/2-BUS MIC/LINE MIXER
WITH PREMIUM MIC PREAMPLIFIERS AND
DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR
USB AUDIO INTERFACE
3
4
7/8
PAM
X 2 .6 2
LAM P
12V
400
mA
USB
INTERFA
CE
SET UP MEMO
Copy this page to fix the set up
PAMX2. 62
Service
All Audio Design PRO products have been inspected and tested before leaving the factory and , if
properly used, they will work for many years. However, in case of any problem, please proceed in the
following way:
Contact your dealer and inform about the defect you found
In case it won't be possible to solve the problem with the dealer, the product needs to be returned,
preferably in its original packaging or in a proper packing to protect it during the transport. Purchase
documents must be produced too.
Your dealer will arrange the shipment to our service centre.
QUICK START
:
Start up:
1.
Turn the power switch OFF.
2.
Set "down" all TRIM controls (all counter clockwise ) and FADER ( all down) .
3.
Center EQ controls (High - Mid - Low) and PAN controls (12 hours).
4.
Set all push buttons in their "off" position (button up).
5.
Set "down" all master section controls (counter clockwise and down)
Connections:
If you already know how you want to connect the mixer, go ahead and connect. If you prefer to inspect
operation, please follow these instructions:
1.
Plug a microphone or a mono signal source into one of the mono channels.
2.
or a stereo signal source into one the stereo channels.
3.
Connect MAIN OUTPUTS to an amplifier (XLR Balanced / Jack Balanced).
4.
Turn power switch on. The blue led (POWER) lights up.
Set the levels:
1.
Push the button "MODE" to use LED level indicators , in PFL mode (Level Set)
2.
Push the button "SOLO " of the channel you intend to set up.
3.
Set the TRIM potentiometer of the channel until the LED indicators (left column) are next to "0" level or
in any case never over +5 level. Avoid absolutely to reach level + 10/Clip.
4.
Release button "SOLO" of the channel you have just set up.
5.
Repeat procedure from point 2 to point 4 for each channel you intend to connect
Mixing:
1.
Set the FADER of each channel at "0" position
2.
Release the button "MODE" to set it in position "SOLO" (NORMAL)
3.
Turn the button "MAIN MIX" to see outlet signal level on the LED indicators.
4.
Turn up "MAIN MIX" to desired level, in relation to the amplifiers / speakers you are using. Preferably,
don't exceed level "0" or "+5" on the LED indicators.
5.
Adjust FADER of each channel to obtain your own mix.
6.
If necessary, adjust tones and repeat above " set levels" procedures
General indications:
1.
The optimum FADER position is near to 0 while the optimum position for the MAIN MIX is the one that
don't exceed level 0 / +5 on the LED level indicators.
2.
Check that the level of each power input is the same that you set up during the "set the levels"
operations, even if you have eventually operated on EQ of each channel. If necessary, each channel can be
adjusted even during the performance through TRIM set up and monitored throught the LED indicators. Avoid
absolutely that CLIP indicator of each channel lights up.
3.
In case you intend to connect further sources, please take care to turn down "MAIN MIX" slider
