AudioCodes MP-104 Quick Start Installation Manual Download Page 9 | Manualshive

Page: 9 / 19

background image

Page 9 of 19

AudioCodes™ MP-104 Gateway Quick Start Installation Guide

August 2004

17.

Click

Apply

. The following blank screen appears.

After a couple of minutes, the BootP status appears, as shown below. If the status does
not appear in the screen, try resetting the client by pressing

RESTART

button using a

long pinhole tool, and click

Apply

.

When complete, four files should have loaded and all four should show “100% OK.”
The green lamps on the LAN and Ready LEDs also light. If not, there is a problem with
the file location. Verify that the file location is accurate and reconfigure the Client Con-
figuration dialog, if necessary.

Follow the instructions on the following pages to launch the MP-104 Web administrator and
configure the application.

«
...
7
8
9
10
11
...
»

Summary of Contents for MP-104




















Reviews:

No comments

Related manuals for MP-104

Brand: B&B Electronics Pages: 60

Brand: Icom Pages: 122

Brand: NeoGate Pages: 41

Brand: Top Global Pages: 75

Brand: SAGEMCOM Pages: 60

Brand: Dinstar Pages: 92

access 1000 series

Brand: MICROTRONIX Pages: 93

Brand: Humanscale Pages: 2

Brand: DatoHome Pages: 6

Brand: Hitron Pages: 2

Brand: ECKELMANN Pages: 58

Lightcloud LCGATEWAY/4G

Brand: RAB Pages: 16

Lightcloud LCGATEWAY

Brand: RAB Pages: 67

Brand: SELECTRONIX Pages: 9

Brand: Divebiss Pages: 45

Brand: Telstra Pages: 100

Brand: 2N Pages: 117

Brand: Eurotherm Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands