AudioCodes Mediant 800 Reference Manual Download

Page: 158 / 195

CHAPTER 7 SNMP Traps

Mediant 800 SBC | SNMP Reference Guide

Alarm

acActiveAlarmTableOverflow

Event Type

processingErrorAlarm

Probable
Cause

resourceAtOrNearingCapacity (43)

Alarm

Severity

Condition

Text

Corrective Action

Major

Too
many
alarms to
fit in the
active
alarm
table

"Active

alarm

table

overflow"

■

Some alarm information may be lost but the
ability of the device to perform its basic
operations is not impacted.

■

A reboot is the only way to completely clear
a problem with the active alarm table.

■

Contact AudioCodes Support.

Remains
'Major'
until
reboot. A
'Clear' trap
is not sent.

After the
alarm is
sent

Note that the status remains 'Major' until reboot
as it denotes a possible loss of information until
the next reboot. If an alarm is sent when the
table is full, it is possible that the alarm is active,
but does not appear in the active alarm table.

Analog Port Alarms

These alarms are applicable only to analog interfaces.

Analog Port SPI Out-of-Service Alarm

The alarm is applicable only to analog interfaces.

Table 7-46: acAnalogPortSPIOutOfService

Alarm

acAnalogPortSPIOutOfService

OID

1.3.6.1.4.1.5003.9.10.1.21.2.0.46

Default
Severity

Major

Source
Varbind

System#0/analogports#<n>, where n is the port number

- 149 -

Summary of Contents for Mediant 800




































































































































































































Search results

Summary of Contents for Mediant 800

Reviews:

Related manuals for Mediant 800

Brands by name

Popular brands

AudioCodes Mediant 800, Reference Manual

Search results

Summary of Contents for Mediant 800

Reviews:

Related manuals for Mediant 800

Brands by name

Popular brands