manualshive.com logo in svg

AudioCodes Mediant 3000 TP-6310, Performance Monitoring And Alarm Manual

Share
Download
AudioCodes Mediant 3000 TP-6310 Performance Monitoring And Alarm Manual Download Page 140

Performance Monitoring and Alarms 

140 

Document #: LTRT-32111 

 

Mediant 3000 with TP-6310 

3.4.49 

DS3 AIS Alarm 

This alarm applies only to Mediant 3000 TP-6310. 

DS3 AIS Alarm 

Description

 

This alarm is issued when the AIS condition is present on the DS3 
Interface #m. 

SNMP Alarm

 

acDS3AISAlarm 

SNMP OID

 

1.3.6.1.4.1.5003.9.10.1.21.2.0.67 

Alarm Title

 

DS3 AIS Alarm 

Alarm Source

 

Interfaces#0/DS3#<m> 

Alarm Type

 

communicationsAlarm 

Probable Cause

 

receiveFailure 

Severity

 

Critical / Cleared 

Additional Info

 

 

Corrective Action

 

Check the following and correct according to the appropriate reason: 

There is a SONET level failure: LOS, LOF, AIS-L, AIS-P, UNEQ-P, TIM-
P 

The far-end (e.g., MUX) sends a DS3 AIS 

 

3.4.50 

DS3 LOF Alarm 

This alarm applies only to Mediant 3000 TP-6310. 

DS3 LOF Alarm 

Description

 

This alarm is issued when the LOF condition is present on the DS3 
Interface #m. 

SNMP Alarm

 

acDS3LOFAlarm 

SNMP OID

 

1.3.6.1.4.1.5003.9.10.1.21.2.0.68 

Alarm Title

 

DS3 LOF Alarm 

Alarm Source

 

Interfaces#0/DS3#<m> 

Alarm Type

 

communicationsAlarm 

Probable Cause

 

receiveFailure 

Severity

 

Critical / Cleared 

Additional Info

 

 

Corrective Action

 

Check and correct the DS3 framing 

 

 

Summary of Contents for Mediant 3000 TP-6310































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands