Audio international DVD-201-01-1 Installation And Operation Manual Download Page 12

Audio International, Inc.

 

 

          DVD-201-01(-02, -03)-x Installation & Operation Manual 

 

 
Document # 540211, Rev C, 05/2002  

                         

Page 11 of 24 

 

6.0   Electrical Characteristics 

 

6.1 Electrical 

Specifications: 

 

Electrical 

Power 

750 mA @ +28 VDC 

 

Operating Voltage 

Range 

+18 to +32 VDC 

 

Data Bus Type 

AI Proprietary RS-485 

 

Audio Frequency 

Response 

4 Hz to 20 kHz 

 

Audio Output 

2 V

RMS 

(factory preset) 

into not less than 600 

 load 

 

Audio Signal to Noise 

Ratio 

>96 dB (NOMINAL) 

 

Dynamic Range 

>93 dB 

 

Video Output 

1 V(p-p) into 75 

, NTSC ONLY

 

Video Input Format 

Multi-Regional (NTSC & PAL) 

 

Infrared Signal Input 

+5 V digital logic level 

 

6.2   The DVD-201-01(-02, -03)-x utilizes one (1) 15-pin connector for electrical 

connections.  This connector provides power, data bus control, infrared 
input, and three (3) infrared strapping pins for alternate configuration of 
infrared digital command codes.  Pin 15 on DVD-201-02-x toggles 
b28 VDC keyline output when the device is playing and ground 
when device is not playing.   
 

6.3 

Standard configuration requires no infrared strap pins to be connected.  
Each different type of AI source equipment can be configured to accept 
one (1) of four (4) different sets of infrared codes.  To change the code 
settings, connect one (1) of the strap pins to the strap common (never 
connect more than one (1) strap pin to the strap common).  Three (3) 
strap pins are available to allow the infrared codes to be configured. 

 

6.4 

The video output connector (BNC1) allows for proper video output to the 
video distribution system. 

 

6.5 

Infrared input provides a ground reference connection (-).  For optimum 
infrared  signal  transmission,  this  ground  reference  connection           
should connect along with the chassis ground reference connection (pin 2) 
to the same ground termination location as that of the IFR-9A or IFR-485 
module being utilized.  If this is not possible, then the infrared ground 
reference connection for the DVD-201-01(-02, -03)-x shall be made within 
12" of the unit. 

 
6.6 

The fiber optic transceiver connector (P2) allows for proper digital audio 
output to the audio distribution system. 

Summary of Contents for DVD-201-01-1


























Reviews: