manualshive.com logo in svg

Audinate Dante MY16-AUD, User Manual, Page: 28 / 58

Share
Download
Audinate Dante MY16-AUD User Manual Download Page 28

Dante-MY16-AUD2 User Guide

Copyright © 2016 Audinate Pty Ltd. All rights reserved.

-28-

Unsupported Dante Network Configurations

Connecting Primary and Secondary redundant networks to the same
switch

When using Dante redundancy with any Dante-enabled device, including Dante-MY16-AUD2 cards, two
separate networks must be used.

You CANNOT connect any secondary network connections to a switch used for the primary network, or
any primary network connections to a switch used for the secondary network.

Please refer to the previous section,

Connection via a Redundant Network

, for information about the

correct configuration to use.

Dante Audio traffic over Wireless Networks

Wireless (Wi-Fi) Ethernet networks should not be used to carry Dante audio traffic, and Audinate
applications installed on a PC or Mac will not allow selection of Wireless Ethernet interface or any other
non-standard wired Ethernet interface.

You should NOT install any wireless components in your Dante network.

Dante-MY16-AUD2: Use of 100Mbps Network interface

The use of 100 Mbps network with Dante-MY16-AUD2 cards is NOT SUPPORTED.

You must only connect Dante-MY16-AUD2 cards to Gigabit interfaces:

n

Gigabit switches, or a Gigabit port on an Ethernet switch

n

Gigabit network interface on a PC or Mac

Summary of Contents for Dante MY16-AUD



























































Reviews:

No comments