manualshive.com logo in svg

Audinate Dante MY16-AUD, User Manual, Page: 25 / 58

Share
Download
Audinate Dante MY16-AUD User Manual Download Page 25

Dante-MY16-AUD2 User Guide

Copyright © 2016 Audinate Pty Ltd. All rights reserved.

-25-

Note: Make sure your Ethernet cables are in good condition and have intact locking tabs.

Remember that Cat5e and Cat6 cabling has a limit of 100 meters at speeds of 1Gbps. If you require longer
distances, you can use fiber.

Network Configuration Options

Straight-through connection to your PC

This configuration is applicable if you want to record and playback directly to and from your PC or Mac, you
are only using one Dante-MY16-AUD2 card, and you do not have any other Dante-enabled audio
equipment.

It is also applicable if you simply need to connect your Dante-MY16-AUD2 card directly to another Dante-
enabled audio device.

In these cases, you can connect your Dante-MY16-AUD2 card to your PC or other Dante-enabled
equipment directly using a standard Cat5e Ethernet cable.

Note: You are REQUIRED to have a Gigabit Ethernet interface on your PC or Mac to directly
connect to your Dante-MY16-AUD2 card.

n

Make sure the PC or Mac is set to automatically configure its IP address

n

Connect the cable between the PC or Mac and the Dante-MY16-AUD2 card

n

You may need to reboot the PC or Mac if it has an active previous IP network configuration

Both devices will automatically be assigned IP network configurations.

Connection via a Gigabit Switch

This configuration is applicable if you have more than just your Dante-MY16-AUD2 card and one PC or
Mac. You will need to use a switch to connect the additional devices to the same network.

In this case, you should connect your PC or Mac(s), your Dante-MY16-AUD2 card(s) and any other Dante-
enabled equipment using a Gigabit switch:

Summary of Contents for Dante MY16-AUD



























































Reviews:

No comments