Audinate Dante MY16-AUD Page 18 User Manual Download | Manualshive

Page: 18 / 58

background image

Dante-MY16-AUD2 User Guide

Copyright © 2016 Audinate Pty Ltd. All rights reserved.

-18-

Ensure the top guide rail sits above the Dante-MY16-AUD2 card.

Removing your card

To remove your Dante-MY16-AUD2 card:

1. Turn off the power to your Yamaha equipment.

2. Unscrew the thumbscrews just enough that they are loose from the host Yamaha equipment, but still

fastened to the Dante-MY16-AUD2faceplate.

3. Using the thumbscrews, pull the card firmly and horizontally towards you to remove.

4. Replace the blank slot cover and its screws.

5. Store the Dante-MY16-AUD2back in its anti-static bag and packaging while not in use.

«
...
16
17
18
19
20
...
»

Summary of Contents for Dante MY16-AUD



























































Reviews:

No comments

Related manuals for Dante MY16-AUD

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: Idis Pages: 123

Brand: Idis Pages: 29

Brand: Idis Pages: 28

DirectIP DR-1304P

Brand: Idis Pages: 82

eBOX532-100-FL Series

Brand: AXIOMTEK Pages: 2

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: XtendLan Pages: 228

ZyXEL ZyAIR B-120

Brand: ZyXEL Communications Pages: 20

Brand: FDI Pages: 2

DataPlot CB1224

Brand: B-G Instruments Pages: 4

ExpressBox2 EB2

Brand: Magma Pages: 74

Brand: Z-Com Pages: 18

Brand: Uniflair Pages: 24

Brand: National Instruments Pages: 56

Brand: AMX Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands