Audinate Dante MY16-AUD Page 14 User Manual Download

Page: 14 / 58

Dante-MY16-AUD2 User Guide

-14-

Specifications

Gigabit Network
support

2 x Gigabit (1000Mbps) Ethernet RJ45 connectors

Redundancy

Supports glitch-free Dante audio redundancy with dual Ethernet networks
(redundant mode)

Daisy chaining

Daisy chain multiple Dante-MY16-AUD2 cards together (switched mode)

Synchronization

High quality on-board VCXO clock can provide master clock OR slave from
audio equipment; automatic synchronization with Dante network

Supported
Sample rates

44.1kHz, 48kHz, 88.2kHz and 96kHz

Sample rate pull-
up/down

+4.1667, +0.1, -0.1, and - 4.0 %

Audio channels

16x16 @ 44.1kHz and 48kHz OR 8x8 @ 88.2kHz and 96kHz

Sample bit depth

16, 24 or 32-bit PCM

Audio format
support

Dante Audio over IP and AES67

HA Remote

Support for HA Remote capable Yamaha products

Expandable

Install up to four Dante-MY16-AUD2 cards in available MY16-compatible slots
for up to 64 bidirectional audio channels

Compatible
Yamaha
equipment:

Compatible with a range of digital mixing consoles, processors and power amps
equipped with MY16-interface compatible card slots, including:

Digital mixers

CS-R10, DSP-R10, RPio622, CL5/3/1, QL5/1, PM5D, DSP5D, M7CL, LS9,
DM2000, DM1000, 02R96, 01V96, 01V96i

Interfaces

RSio64-D

Processors

MRX7-D, MTX5-D, DME24N, DME64N

Power amps

Tx4n, Tx5n, Tx6n

Summary of Contents for Dante MY16-AUD


























































Search results

Summary of Contents for Dante MY16-AUD

Reviews:

Related manuals for Dante MY16-AUD

Brands by name

Popular brands

Audinate Dante MY16-AUD, User Manual

Search results

Summary of Contents for Dante MY16-AUD

Reviews:

Related manuals for Dante MY16-AUD

Brands by name

Popular brands