manualshive.com logo in svg

Audi 2003 A8, Workshop Manual

The Audi 2003 A8 Workshop Manual is a comprehensive guide for car enthusiasts and professional mechanics alike. This invaluable resource provides step-by-step instructions and diagrams, allowing users to confidently tackle any repair or maintenance task. Download this manual for free at manualshive.com and unlock the full potential of your Audi A8.

Share
Download
background image

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not 
 permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability 
     with respect to the correctness of information in this document. Copyright by AUDI AG.

– Unplug electrical connector -2- at oil level and oil temperature

sender - G266- .

– Drain off engine oil ⇒ Maintenance ; Booklet  404 .
– Unbolt sump (bottom section) -1- and carefully release it from

bonded joint.

Note

There will still be some oil in the sump (bottom section).

Installing

Note

Renew seals.

WARNING

Wear safety goggles.

– Remove sealant residue from bottom and top sections of sump

with rotating plastic brush or similar.

– Clean sealing surfaces; they must be free of oil and grease.

Note

Note the use-by date of the sealant.

– Cut off tube nozzle at front marking (diameter of nozzle ap‐

prox. 2 mm).

Audi A8 2003 ➤

10-cylinder direct petrol injection engine (5.2 ltr. 4-valve), mechanics - Edition 10.2013

162

     Rep. gr.17 - Lubrication

Summary of Contents for 2003 A8





























































































































































































































































Reviews:

No comments

Related manuals for 2003 A8

Eaton-Williams Qualitair Technical Manual & Installation Procedures preview
Qualitair
Brand: Eaton-Williams Pages: 10
Haier HBU-28CF03 Installation Instructions Manual preview
HBU-28CF03
Brand: Haier Pages: 14
Haier HWR05XC9 Instrucciones De Operación preview
HWR05XC9
Brand: Haier Pages: 20
Haier HWF05XC7 Manual De Usuario preview
HWF05XC7
Brand: Haier Pages: 20
Haier HW-07LM03 Operation Manual preview
HW-07LM03
Brand: Haier Pages: 12
Haier HSU18VH7 Manual preview
HSU18VH7
Brand: Haier Pages: 36
Haier HWE18VCN User & Care Manual preview
HWE18VCN
Brand: Haier Pages: 100
Haier HSU-24C03 Manual preview
HSU-24C03
Brand: Haier Pages: 24
Haier H2SM- Manual preview
H2SM-
Brand: Haier Pages: 19
Haier H2SM- Operating Manual preview
H2SM-
Brand: Haier Pages: 99
Haier ESA3156 - ANNEXE 221 Manual preview
ESA3156 - ANNEXE 221
Brand: Haier Pages: 25
Haier ESA3159 User Manual preview
ESA3159
Brand: Haier Pages: 26
Haier ESA3159 Manuel preview
ESA3159
Brand: Haier Pages: 25
Haier AU222XHBAA Manual preview
AU222XHBAA
Brand: Haier Pages: 19
Haier HSU-22H03/R2 Manual preview
HSU-22H03/R2
Brand: Haier Pages: 25
Haier ESA3067 - annexe 1 Manuel preview
ESA3067 - annexe 1
Brand: Haier Pages: 22
Haier HWR05XC5 Manual preview
HWR05XC5
Brand: Haier Pages: 19
Argo AEI1G140EMX3PH Installation Instructions Manual preview
AEI1G140EMX3PH
Brand: Argo Pages: 92

Brands by name

Popular brands

Load more brands