Auber Instruments EZboil DSPR310D Page 14 Instruction Manual Download | Manualshive

Page: 14 / 14

background image

AUBER INSTRUMENTS

WWW.AUBERINS.COM

2018.08

P14/14

Figure 8. A 50% output control signal from DSPR when it is operating in the bust firing mode. Each pulse is 16.67 ms long, which is the same as a 60 Hz AC cycle.

So one pulse on and one pulse cycle off is equal to 50% output.

Figure 9. The DSPR control signal and SSR output waveform overlaid. The DSPR detects the frequency and phase of the AC power line, so that the pulse width and
firing time is synchronized with AC cycle.

Auber Instruments

5755 North Point Parkway, Suite 99

Alpharetta, GA 30022

www.auberins.com

Email: [email protected] Tel: 770-569-8420

Copyright 2007-2018, Auber Instruments All Rights Reserved.

No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written consent of Auber Instruments. Auber Instruments retains the

exclusive rights to all information included in this document.

«
...
12
13
14

Summary of Contents for EZboil DSPR310D















Reviews:

No comments

Related manuals for EZboil DSPR310D

Brand: E-fly Pages: 16

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 11

Brand: Nauticam Pages: 2

Brand: National Instruments Pages: 18

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 20

GEMINI C Series

Brand: NAPCO Pages: 24

Brand: Valcom Pages: 6

Brand: Zodiac Pages: 12

Brand: National Instruments Pages: 34

Brand: Parker Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands