Atmel AT91SAM-ICE User Manual Download

Page: 5 / 27

AT91SAM-ICE User Guide

1-1

6206B–ATARM–04-Mar-08

Section 1

Introduction

1.1

Overview

SAM-ICE is a JTAG emulator designed for Atmel

AT91 ARM

cores. It connects via USB to a PC run-

ning Microsoft Windows2000 or XP. SAM-ICE has a built-in 20-pin JTAG connector, which is compatible
with the standard 20-pin connector defined by ARM

1.1.1

Features of SAM-ICE

Any Atmel AT91 ARM7

™

/ARM9

™

core supported, including Thumb

mode

Seamless integration into the IAR

Workbench

No power supply required, powered through USB

Maximum JTAG speed 8 MHz

Auto speed recognition

All JTAG signals can be monitored

Support for multiple devices

Fully plug and play compatible

Standard 20-pin JTAG connector

Wide target voltage range: 1.2V to 3.3V

USB and 20-pin ribbon cable included

Real-time memory viewer (J-Mem) included

SAM-ICE TCP/IP server included, can use SAM-ICE via TCP/IP networks

RDI server available, can use SAM-ICE with RDI compliant software

Support for adaptive clocking

1.1.2

Specification

Table 1-1. SAM-ICE Specification

Parameter

Power Supply

USB powered < 50mA

USB Interface

USB 2.0, full speed

Target Interface

JTAG 20-pin

Serial Transfer Rate between SAM-ICE and Target

Up to 8 MHz

Supported Target Voltage

1.2V to 3.3V

Operating Temperature

+5°C to +60°C

Storage Temperature

-20°C to +65 °C

Summary of Contents for AT91SAM-ICE




























Search results

Summary of Contents for AT91SAM-ICE

Reviews:

Related manuals for AT91SAM-ICE

Brands by name

Popular brands

Atmel AT91SAM-ICE, User Manual

Search results

Summary of Contents for AT91SAM-ICE

Reviews:

Related manuals for AT91SAM-ICE

Brands by name

Popular brands