manualshive.com logo in svg

Atmel AT90S8414, Manual

Share
Download
Atmel AT90S8414 Manual Download Page 62

4-62

 AT90S8414 

Preliminary  

 

Table 18: DDBn Effects on Port B Pins

DDBn

PORTBn

I/O

Pull up

Comment

0

0

Input

No

Tri-state (Hi-Z)

0

1

Input

Yes

PBn will source current (IIL) if ext. pulled low.

1

0

Output

No

Push-Pull Zero Output

1

1

Output

No

Push-Pull One Output

n: 7,6…0, pin number.

ALTERNATE FUNCTIONS FOR PORTB

The alternate pin configuration is as follows:

SCK - PORTB, Bit 7:

SCK: Master clock output, slave clock input pin for SPI channel

MISO - PORTB, Bit 6:

MISO: Master data input, slave data output pin for SPI channel

MOSI - PORTB, Bit 5:

MOSI: SPI Master data output, slave data input for SPI channel

SS - PORTB, Bit 4:

S S

 (Slave port select input)

AIN1 - PORTB, Bit 3

AIN1, Analog Comparator Negative Input. When configured as an input (DDB3 is cleared (zero)) and with the internal
MOS pull up resistor switched off (PB3 is cleared (zero)), this pin also serves as the negative input of the on-chip analog
comparator.

AIN0 - PORTB, Bit 2

AIN0, Analog Comparator Positive Input. When configured as an input (DDB2 is cleared (zero)) and with the internal
MOS pull up resistor switched off (PB2 is cleared (zero)), this pin also serves as the positive input of the on-chip analog
comparator.

T1 - PORTB, Bit 1:

T1, Timer/Counter1 counter source: The PB1 pin has to be configured as an input (DDB1 is cleared (zero)) to serve this
function. See the timer description for further details. The internal pull up MOS resistor can be activated as described
above.

T0 - PORTB, Bit 0:
T0: Timer/Counter0 counter source: The PB0 pin has to be configured as an input (DDB0 is cleared (zero)) to serve this
function. See the timer description for further details. The internal pull up MOS resistor can be activated as described
above.

Summary of Contents for AT90S8414
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands