AT04357 RCB256RFR2-XPRO User Guide [USER GUIDE]
TBDA-MCU-09/2013
18
as specified in the user manual. If any of these specifications are exceeded in the final product, a submission
must be made to a notified body for compliance testing to all required standards.
Important
The 'CE' marking must be affixed to a visible location on the OEM product. The CE mark shall
consist of the initials "CE" taking the following form:
The CE marking must have a height of at least 5mm except where this is not possible on account
of the nature of the apparatus. The CE marking must be affixed visibly, legibly, and indelibly. More
detailed information about CE marking requirements you can find at "DIRECTIVE 1999/5/EC OF
THE EUROPEAN PARLIAMENT AND OF THE COUNCIL" on 9 March 1999 at section 12.
5.3
Canada (IC)
The ATRCB256RFR2-XPRO Module complies with Industry Canada specifications RSS-210 and RSS – GenIC
ID for ATRCB256RFR2-XPRO is 11019A-092007
ATRCB256RFR2-XPRO is limited modular approved and required separate approval for this module when
used on an application board.
User manuals for licence-exempt radio apparatus shall contain the following or equivalent notice in a
conspicuous location in the user manual or alternatively on the device or both.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
This equipment complies with radio frequency exposure limits set forth by Industry Canada for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm between the
device and the user or bystanders.
Cet équipement est conforme aux limites d'exposition aux radiofréquences définies par Industrie Canada pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de
distance entre le dispositif et l'utilisateur ou des tiers
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. The OEM integrator is still responsible for testing their end-
product for any additional compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.).
This Module is labelled with its own IC ID. If the IC ID Certification Number is not visible while installed inside
another device, then the device should display the label on it referring the enclosed module. In that case,
the final end product must be labelled in a visible area with the following: “Contains Transmitter Module
IC:11019A-092007 ” (Mention IC ID) OR “Contains IC: 11019A-092007 ”
Ce module est étiqueté avec son propre ID IC. Si le numéro de certification IC ID n'est pas visible lorsqu'il est
installé à l'intérieur d'un autre appareil, l'appareil doit afficher l'étiquette sur le module de référence ci-joint.
Dans ce cas, le produit final doit être étiqueté dans un endroit visible par le texte suivant: “Contains Transmitter
Module IC: 11019A-092007 ” OR “Contains IC: 11019A-092007 ”
5.4
Using Limited Modular Certified Products
The ATRCB256RFR2-XPRO Module is certified under part 15 of FCC rules. The Modular certification category
of this module is “Limited Modular”. The End product using these modules hence has to undergo compliance
testing and receive a new FCC ID for the final product carrying these modules. Certification of the final product
lies solely with the type of design of the final product, excluding the ZigBit.
