manualshive.com logo in svg

Atlas SunSpray, Operating Manual, Page: 9 / 28

Share
Download
Atlas SunSpray Operating Manual Download Page 9

- 9 -

Operating Manual SunSpray for SUNTEST

®

 XLS+

1

Instructions for safe operation

 

1.2  General safety instructions

Safety devices

The SunSpray device is equipped with a safety switch which monitors the function of the unit.

•   A float switch turns off the unit as soon as the fill level of the water reservoir drops below a minimum level

After the instrument turns off due to a fault, operation cannot continue until the error message is confirmed. An 

 

interrupted test continues at the point at which it was interrupted.

Incoming power connection

The device can be operated with the following voltages:

•   230 V ± 10 %, 50 / 60 Hz

The device is manufactured for the power supply network according to the confirmed sales order.

 

 

 Disposal:

   

 

OBServe The reguLaTIOnS FOr dISPOSaL!

Since March 24, 2006 the manufacturer is obliged to take back the product 

according to the European directive 2002/96/EG WEE (Waste Electrical and 

Electronic Equipment) in the corresponding national version.

Compliance with the RohS directive:

The SUNTEST

®

 XLS+ meets the requirements of the 2002/95/EG RohS directive (restriction of the use of certain 

hazardous substances in electrical and electronic equipment) for equipment class 9.

Disposal of the packaging:

Please dispose of the packaging materials according to any local disposal regulations. A list of used packaging  

materials can be found in chapter 2, section 2.1, “Packaging”.

Summary of Contents for SunSpray





























Reviews:

No comments