Atlas SunSpray Operating Manual Download Page 8 | Manualshive

Page: 8 / 28

Atlas SunSpray Operating Manual Download Page 8

Operating Manual SunSpray for SUNTEST

®

XLS+

- 8 -

1

Instructions for safe operation

1.2 General safety instructions

Use for the intended purpose:

• The SunSpray device serves as an accessory for the SUNTEST

®

XLS+ for sample spraying and may only be used

in combination with the SUNTEST XLS+

• The SunSpray sprays water and provides the possibility of implementing wet cycles in weathering tests (see

installation instructions for data on water quality)

• The device is suitable for continuous operation

• The SunSpray device is tested for electromagnetic compatibility and suitable for installation in an industrial

environment

Improper use

• The SunSpray device may not be operated in rooms which do not meet the installation requirements

• No other spraying liquids apart from purified water may be used

This device meets the following safety requirements:

• DIN EN 61010, Part 1 Edition 2002-08

Safety regulations for electrically operated measuring, control, regulating and laboratory instruments.

General requirements

Equipping of high voltage systems with electronic equipment

• DIN EN 60204 (DIN VDE 0113): Part 1 Edition 1998-11

Electrical equipping of industrial machines

• DIN EN 60947-1 Edition 1999-12

Low-voltage switchgear

• DIN EN 60947-3 Edition 2001-12

Low-voltage switchgear

• DIN EN 50274 Edition 2002-11 and DIN EN 60529-1 Edition 2000-09

Finger safety, back of hand safety

• DIN EN 61326 EMC

• DIN EN 61000 EMC

«
...
6
7
8
9
10
...
»

Summary of Contents for SunSpray





























Reviews:

No comments