manualshive.com logo in svg

Atlas SunSpray, Operating Manual, Page: 5 / 28

Share
Download
Atlas SunSpray Operating Manual Download Page 5

- 5 -

Operating Manual SunSpray for SUNTEST

®

 XLS+

Instructions for the user:

This operating manual describes the SunSpray accessory (spraying unit) for the SUNTEST

®

 XLS+ weathering instru-

ment.

Please note that certain work may only be carried out by personnel with the proper qualification.

The following persons can be considered properly qualified:

•   Persons who have gained their knowledge in special training courses

•   Persons who have been trained for the operation and operating possibilities of the SUNTEST XLS+ instrument 

and the accessory based on this operating manual

•   Persons who are able to assess the activity that they perform based on work experience and instruction in the 

relevant safety conditions and recognize possible hazards

 

Service:

•   Work on the electrical components may only be carried out by qualified personnel

Cleaning:

•   Cleaning work on the accessories may only be carried out by trained personnel with instruction based on this 

operating manual

Please read this operating manual carefully before using the accessory for the first time in order to be able 

to use the existing scope of functions and to avoid possible damage to the accessory.

If special problems occur which are not explained in enough detail in this operating manual, please contact 

your supplier for your own safety.

1

Instructions for safe operation

 

Summary of Contents for SunSpray





























Reviews:

No comments