Atlas Copco XAS 185 KDU T4F HOP Instruction Manual Download Page 46

Page: 46 / 62

- 46 -

LUBRICATION OILS

It is strongly recommended to use Atlas Copco branded lubrication oils for compressor.

Compressor oil

Engine oil

Engine coolant

(1) Additional equipment is needed to run the compressor below 18°F. Please contact

Atlas Copco for more information about Cold Weather Packages

* Keep the bolts of the housing, the lifting eye, the towbar and the axle

securely tightened. Refer to Compressor/Engine Specifications for the

torque values.

PAROIL - M Xtreme

Order number

1.3 gallon pail:

1615 5947 00

5 gallon pail:

1615 5948 00

55 gallon drum:

1615 5949 00

PAROIL - S

Order number

1.3 gallon pail:

1630 0160 00

5 gallon pail:

1630 0161 00

55 gallon drum:

1630 0162 00

264 gallon container:

1630 0163 00

PAROIL - EXTRA

Order number

1.3 gallon (5 Liter) Container:

1630 0135 01

5 gallon (20 Liter) Pail:

1630 0136 01

PAROIL - E MISSION GREEN

Order number

1.3 gallon (5 Liter) Container:

1630 0471 00

5 gallon (20 Liter) Pail:

1630 0472 00

55 gallon ( 209 Liter) Drum:

1630 0473 00

PARCOOL - EG

Order number

1.3 gallon container:

1604 8159 00

5 gallon pail:

1604 5307 01

55 gallon drum:

1604 5306 00

Temperature Range

Type of Oil

Compressor

Engine

Between -13°F and 122°F

(1)

PAROIL

See Engine Operation Manual

Between 18°F and 104°F

PAROIL

M Xtreme

15W-40

Operation of compressor in ambient temperatures lower than 18°F (-8°C)

without the correct type of oil will void your warranty and may result in

element failure and/or fire.

Summary of Contents for XAS 185 KDU T4F HOP































































Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Brands by name

Popular brands

Atlas Copco XAS 185 KDU T4F HOP, Instruction Manual

Search results

Summary of Contents for XAS 185 KDU T4F HOP

Reviews:

Brands by name

Popular brands