background image

I

NSTRUCTION

M

ANUAL

33

8.

TECHNICAL SPECIFICATIONS

8.1

T

ORQUE VALUES

8.1.1 F

OR GENERAL APPLICATIONS

The following tables list the recommended torques applied for general applications
at assembly of the compressor.

For hexagon screws and nuts with strength grade 8.8

Thread size

M6

M8

M10

M12

M14

M16

Nm

9

23

46

80

125

205

For hexagon screws and nuts with strength grade 12.9

Thread size

M6

M8

M10

M12

M14

M16

Nm

15

39

78

135

210

345

8.1.2 F

OR IMPORTANT ASSEMBLIES

Assemblies

Unit

Torque values

Wheel bolts

Nm

140 – 150

Axle/frame screws (M16)

Nm

185 – 225

Axle/frame screws (M12)

Nm

75 – 85

Bolts, towbar/axle (M12)

Nm

75 – 85

Screws, towbar/frame (M12)

Nm

75 – 85

Screws, lifting eye/flywheel housing

Nm

190 – 200

Screws, coupling half/coupling

Nm

80 – 90

Screws, towing eye/towbar (M12)

Nm

75 – 85

Nuts, engine outlet collector/silencer

Nm

50 – 55

Nuts, brake cable/wheel plate

Nm

15 – 25

Note:
Secure the tank cap and drain cock of the fuel tank handtight.

8.2

S

ETTINGS OF SHUT

-

DOWN SWITCHES AND

SAFETY VALVES

Designation

Unit

Engine temperature

°C

150 - 155

Engine oil pressure

bar(e)

1.14 - 0.8

Compressor temperature

°C

116 – 120

Safety valve opening pressure

EC type

bar(e)

9.5

8.3

C

OMPRESSOR

/

ENGINE SPECIFICATIONS

Compressor type

XA(S)175 Dd

Reference conditions

1.

Absolute inlet pressure

bar

1

2.

Relative air humidity

%

0

3.

Air inlet temperature

°C

20

4.

Normal effective working pressure

bar

12

The inlet conditions are specified at the air inlet grating outside the canopy

Performance data 

1.

Engine shaft speed, normal and maximum

r/min

2300-2390

2.

Engine shaft speed, compressor unloaded

r/min

1400

3.

Free air delivery

l/s

173

4.

Compressed air temperature at outlet valves

°C

85

5.

Noise level (XAS175 Dd)

Sound pressure level (LP), measured according to
ISO 2151 with a tolerance of +/- 3 dB(A) under free
field conditions at 7 m distance

dB(A)

74

Sound power level (LW) complie with 84/533/EEC limits

dB(A)

102

Design data

Compressor

1.

Number of compression stages

1

Engine

1.

Make

KHD

2.

Type

F6L913

3.

Coolant

OIL/AIR

4.

Number of cylinders

6

5.

Output according to DIN ISO 3046 IFN at normal shaft speed

kW

79

Unit

1.

Capacity of compressor oil system

l

30

2.

Nett capacity of air receiver

l

60

3.

Capacity of fuel tank

l

150

Unit dimensions

(with standard towbar)

Length

mm

4380

Width

mm

1670

Height

mm

1530

Weight (dry)

kg

1630

Outlet valve specifications
Number

diameter

3

3/4”

1

1 1/2”

Summary of Contents for XAS 175 Dd



































Reviews: