Atlas Copco HiLight H6+ DC Instruction Manual Download Page 25

Page: 25 / 116

- 25 -

Once all the above operations are complete, you will
have returned the light tower to the same state as it
was before the positioning procedure (see figure
above). At this point the light tower is correctly
arranged for transport.

3.2.4

Towing

Before commencing towing, ensure you follow the
procedure below:

1. Check that the coupler (1) of the undercarriage of

the light tower is safely coupled to the towing
hook of the towing vehicle.

2. Connect the cabling plug to the towing vehicle so

that the rear lights of the light tower work
(indicators, lights, brake lights).

3. Check that the pressure and condition of the tires

are suitable for the road and the climatic
conditions.

4. Release the handbrake (2), if provided.

Do not proceed with towing if you
notice any broken or faulty parts.

Drive carefully according to the
road and climatic conditions.

Keep in mind that for the low speed
off-road non-homologated trailer,
the maximum speed is 20 Km/h!

00_00_HiLight H6+_EN.book Page 25 Friday, June 4, 2021 11:52 AM

Summary of Contents for HiLight H6+ DC





















































































































Search results

Summary of Contents for HiLight H6+ DC

Reviews:

Atlas Copco HiLight H6+ DC, Instruction Manual, Page: 25 / 116

Search results

Summary of Contents for HiLight H6+ DC

Reviews: