manualshive.com logo in svg

Atlas Copco GA 11 VSD, Instruction Book

Share
Download
Atlas Copco GA 11 VSD Instruction Book Download Page 69

7

Adjustments and servicing procedures

7.1

Drive motor

General

Never mix greases of different brands or types.
Keep the outside of the electric motor clean for efficient cooling. If necessary, remove
dust with a brush and/ or compressed air jet.

GA 11 VSD

The correct grease type can be ordered from Atlas Copco; see section 

Service kits.

For the regreasing interval see section 

Preventive maintenance schedule.

The bearings must be regreased with KLÜBERQUIET BQH 72-102

Quantity: 16 g (0.56 oz) per bearing at the drive end side

Quantity: 10 g (0.35 oz) per bearing at the non-drive end side

To regrease the motor, run the regreasing program from the ‘Test’ submenu on the regulator.

During the regreasing program, the compressor will run for 15 minutes at low speed. The
compressed air is blown off via the solenoid valve.

After carrying out all service actions in the relevant ‘Service Plan’, reset the service warning; see
section 

Service menu.

The compressor can be put into operation again by pressing the start button.

Instruction book

API161475

67

Summary of Contents for GA 11 VSD





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands