manualshive.com logo in svg

Atlantic HPWH 200 Lt, Installation And Operation Manual, Page: 7 / 39

Share
Download
Atlantic HPWH 200 Lt Installation And Operation Manual Download Page 7

Overview   

InstallaBon   

OperaBon   

Maintenance   

Warranty   

DescripJon   

1.   Important   recommendaJons   

1.1.   Safety   direcJves   

InstallaBon    and    commissioning    work    on    the    heat    pump    water-­‐heaters    may    pose    hazards    because    of    high-­‐

pressure   and   live   electrical   parts.   

Heat   pump   water   heaters   must   be   installed,   serviced   and   maintained   by   trained   and   qualified   personnel   only.   

1.2.   Transport   and   storage   

The    product    may    be    turned    through    90°    on    one    side.    The    side    permiVed    is   

shown   clearly   on   an   informaJon   label   placed   on   the   product   packaging.   The   

product   must   not   be   turned   on   the   other   sides.   An   inclinaJon   indicator   is   used   
to    check    that    the    product    has    been    transported    and    handled    in    accordance   

with   our   recommendaJons.   We   recommend   you   should   be   careful   to   respect   
these    instrucJons.    Our    warranty    will    not    apply    if    the    inclinaJon    indicator    is   

red.    We    will    not    be    responsible    for    any    fault    in    the    product    resulJng    from   

transport   or   handling   of   the   product   in   a   way   that   does   not   comply   with   our   
recommendaJons.   

2.   Content   of   package   

Water   heater   

1   tube   for   condensates   (2m)   

1   Manual   

1   bag   with   insulaBon   sleeve   with   2   seals   to   be   fiTed   to   the   

hot   water   outlet   

Coil   model   only:   an   other   addiBonal      insulaBon   sleeve   is   

provided   to   be   fiTed   to   the   recirculaBon   fijng.   

1   metal   strap   and   screw   to   fix   the   device   on   the   ground   

1   x   700   kPa   PT   safety   valve   &   tee   piece   to   be   installed   on   

the   hot   water   outlet   

   

1   connecBon   for   evacuaBon   of   the   condensates   

6   

Summary of Contents for HPWH 200 Lt








































Reviews:

No comments