Atlanta BWL 108e Document Procedure Download Page 1

BWL 108e 

 

 

 

 

 

D o c u m e n t e d   p r o c e d u r e

 

4100-001-12.93 

Abteilung 

TB/Steinbach 

Seite 

Änd. Index 

Name 

Steinbach 

12.03.98 

Datum 

27.02.06 

Operating and maintenance 

instructions 

freigegeben  TB/Lorch 

12.03.98 

 

00000407584841494444.DOC 

ATLANTA ball-screw gripping nut with cut-off 

 
 

Variants 

1.  Ball-screw gripping nut without ball-screw supporting nut 

2.  Ball-screw gripping nut with ball-screw supporting nut 

3.  Ball-screw gripping nut with ball-screw supporting nut and safety sleeves 

 

Functional description 

The gripping nut must be located in load direction behind the supporting nut. It features the counter 
profile of the ball-screw spindle. During normal operation it is centred on the ball-screw supporting nut 
and moves along without contact. It becomes engaged only when the balls get lost out of the ball-
screw nut. Then the spindle is pulled through the ball-screw nut and the gripping nut is pressed 
against the supporting nut thus triggering the limit switch and cutting off the drive. 
The sleeves in the bores of the ball-screw nut are safety elements especially for set-up purposes. 
During normal operation the drive is cut off by means of limit switches provided at the lifting table or at 
the respective plant before the table or the plant reaches its mechanical end position. When during 
set-up operation these limit switches are inoperative it is possible to move up to the mechanical end 
position, i.e. until it blocks, which may cause damage to the drive mechanism. Due to the sleeves in 
the ball-screw nut the nut can continue to move on  the driven spindle for a short distance when the 
mechanical end position of the table or the plant is reached. After approx. 5 mm the table/plant is 
switched off by the limit switch. Furthermore it is also possible to recognise optically that the nut is still 
moving. 
 
Mounting 

Variant 1: 

The gripping nut is supplied preassembled. For mounting the ball-screw nut the gripping nut must be 
screwed upon the spindle. Push the clamping ring over the supporting nut until the dimension L is 
reached. Then fix the clamping ring with the clamping screw on the nut. Make sure that the gripping 
nut and the spindle move without contact. 
Quality of clamping screw: 10.9 or 12.9 
Stud torque: 14 Nm with torque spanner 
Secure the screw with Loctite 243. 
Mount the limit switch with support as shown on the drawing on the next page observing the 
dimension 1 mm, and check whether the roller is positioned in the middle of the groove. If necessary, 
loosen the clamping ring and adjust the position of the supporting nut.  
 

Order code 

Size of ball-screw 

Dyn. capacity 

Dimension L 

Dimension L1 

63 25 720 

50x10 

78 kN 

60 

97 

63 25 725 

50x20 

82 kN 

58 

95 

63 25 727 

50x20 

96 kN 

87 

122 

63 25 726 

50x20 

160 kN 

84 

132 

63 25 730 

60x10 

86 kN 

60 

99 

63 25 735 

63x20 

85 kN 

60 

99 

63 25 736 

63x20 

248 kN 

141 

180 

63 25 748 

80X20 

359 kN 

141 

185 

 

Reviews: