Atlanta Attachment Company 1315A Technical Manual & Parts Lists Download | Manualshive

Page: 22 / 106

background image

Technical Manual & Parts Lists

16

Efka Parameter Settings

(Sewing Head Motor)

Programming Instructions

Power on holding down the “P” button until “COD” is displayed.
Press “>>” once and enter the number “311”
Press “E” once and “2.0.0” is displayed. This is a parameter.
Proceed to the parameter to be changed and press “E”.
The value now shows in the screen. Adjust to desired value.
Press “E” to enter value and continue with parameter setting.
Repeat for other parameters. Press “P” one time when complete.
Run sewing head to save parameters before powering down.

To Perform Master Reset of Parameters

Power on holding down the “P” button until “COD” is displayed.
Press “>>” one time and enter the number “591”
Press “E” twice and “093” is displayed.

Press “+” once, “094” is displayed.
Press “P” to exit programming mode with all default values.

Parameter

Range

Value

Description

290

0-26

5

Mode of Operation. MUST BE SET FIRST!

111

400-9900 rpm

320

Maximum side speed.

112

200-9900 rpm

20

Minimum corner speed.

113

200-9900 rpm

100

Maximum corner speed.

114

400-9900 rpm

150

Auxiliary sewing speed.

124

200-9900 rpm

990

Maximum possible for minimum side speed.

125

200-9900 rpm

200

Minimum side speed.

153

0-50

35

Braking power at machine stand still.

161

0-1

0=CW

Motor Rotation

202

0-500

500

Sew start delay after footlift off.

204

1-100

100

Holding power of footlift (disables footlift chopping).

219

20090

35

Braking power at stop of the drive.

220

20090

5

Sew start acceleration of the drive.

224

0-1

0

Speed gate 2 on/off

270

0-5

1

External handwheel sensor configuration.

271

0-255

165

Ref angle for Pos 1 (ndl down) from Pos 2 (ndl up tape)

272

020-255

100

Drive ratio between motor pulley and handwheel pulley. If handwheel
pulley is smaller than motor pulley, increase this value to slow down
sewing head until measured speed matches speed set with parameter
111. (For Yamato and Pegasus, setting should be 100; for Rimoldi,
setting should be 124)

436

0

Use code "5913". This disables an input that was causing box to reset
itself.

Front Panel LED’s:

LED 1-6: Off, LED 7: On, Stop at needle down, LED 8: Off

From

the

library

of:

Diamond

Needle

Corp

«
...
20
21
22
23
24
...
»

Summary of Contents for 1315A











































































































Reviews:

No comments

Related manuals for 1315A

Brand: ZOJE Pages: 28

Brand: General Pages: 20

Brand: Nilfisk-ALTO Pages: 84

Brand: Janome Pages: 44

Brand: Tornado Pages: 54

Brand: R+M Suttner Pages: 4

Little Misty LM-1

Brand: Talent Pages: 6

CONTOUR 350 DELUXE

Brand: H. Winter Pages: 23

Brand: A-S-S Pages: 7

4182i 100 Series

Brand: Minerva Boskovice Pages: 38

Brand: JUKI Pages: 9

Brand: JUKI Pages: 4

Brand: Janome Pages: 92

Brand: Gamma Pages: 20

Brand: Duerkopp Adler Pages: 36

Brand: Toshiba Pages: 33

Brand: Toshiba Pages: 33

Brand: Toshiba Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands