Atlanta Attachment Company 1315A Technical Manual & Parts Lists Download | Manualshive

Page: 21 / 106

background image

Technical Manual & Parts Lists

15

Electric Eye Sensor Adjustment

To adjust the sensor, first remove the clear plastic cover from the end of the sensor. There are

two adjusting screws under the cover. One is labeled “GAIN” and is used to set the sensitivity of the
sensor. The other screw is labeled “DO & LO” and should always be fully clockwise.

With the end of the sensor pointing at the center of the reflective tape, turn the “GAIN” screw

counter-clockwise until the red LED indicator is off. Then turn the “GAIN” screw clockwise until the
LED indicator comes on. Then turn the “GAIN” screw one full turn clockwise. The LED indicator
should be blinking slowly. Cover the eye so that the sensor cannot see the reflective tape and the LED
should go off.

Reflective Tape Maintenance

Use a soft cloth for cleaning.
Do not use chemicals or abrasives to clean it.
Avoid any contact with oils and liquids.
Do not touch the tape with bare fingers.
If tape is dirty or opaque, the eye may not function correctly.

From

the

library

of:

Diamond

Needle

Corp

«
...
19
20
21
22
23
...
»

Summary of Contents for 1315A











































































































Reviews:

No comments

Related manuals for 1315A

Brand: Cafection Pages: 82

Memory Craft 6300P

Brand: Janome Pages: 69

GPS/F-1006 Series

Brand: Garudan Pages: 114

Brand: Samyung Pages: 87

Brand: SCANMASKIN Pages: 60

Brand: Bright Solutions Pages: 21

Brand: dj power Pages: 12

Brand: Akerworks Pages: 2

BP27 ULTRA MAXX

Brand: NSS Pages: 20

Brand: Euro-Pro Pages: 46

Brand: JUKI Pages: 149

Brand: JUKI Pages: 120

Brand: JUKI Pages: 12

Brand: Club Piscine Pages: 10

Brand: Canon Pages: 116

Brand: Canon Pages: 7

Brand: Canon Pages: 13

Brand: Canon Pages: 139

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands