manualshive.com logo in svg

Athena 1090 EVO, Translation Of Original Instructions, Page: 127 / 182

Share
Download
Athena 1090 EVO Translation Of Original Instructions Download Page 127

 

127 

 

Recharge the battery only in ventilated areas. 

With the main switch QS1 (battery disconnect switch) turned to the ON position, 

connect  the  positive  pole  of  the  battery  charger  to  the  150A  fuse  or  to  the 

dedicated connector placed under the ladder; connect the negative pole of the 

battery 

charger 

to 

the 

frame.     

 

Disconnect  the  battery  charger  when  the  relative  indicator  shows  that  the 

battery is charged. 

Connect  the  battery  charger  to  an  electric  power  supply  that  conforms  to  the 

following specifications: 

•

 

Voltage: 230 v ± 10% 

•

 

Frequency: 50 Hz 

•

 

Grounding line working and equipped with a differential circuit breaker 

•

 

Use  an  extension  power  cord  with  an  appropriate  section  depending  on  its 

length 

 

 

6.2.9.3.2  Charging method No. 2 using the 230V plug in the ladder 

If the machine is equipped with a 230V electric motor, it is possible to recharge the 

battery simply by connecting the plug in the ladder to the external power source.  

The 230V AC/12V DC converter will recharge the battery 

Summary of Contents for 1090 EVO























































































































































































Reviews:

No comments