background image

4/12 

 

Socket (optional) 

It’s  possible  to  include  up to two  in-built sockets (receptacles) for linking  unit in series with other 
SLAM Star or SLAM Hornet units. 

Accessories 

  Antistatic protective film for PC tube against chemical splashes and other substances 

  SLAM Star Magnet set for wall mounting 

To view options on accessories, please visit 

www.atexor.com

 or call us di358 20 734 3250. 

1.3  Certification of equipment 

SLAM Star has been designed, tested and certified for portable use. 

The  equipment  is  to  be  used  properly  and  according  to  its  ratings,  documentation  and  local 
applicable laws. Local, national certificates of the unit may exist outside the region of EU. 

The aforementioned SLAM Star is certified as follows. You may find brief explanation of certificate 
beneath. 

 

CE

0537

  

II 2 G  Ex e mb op is IIC T4 Gb 

 

IP 66 

CE

0537

  =  Valid  production  quality  system  approved  and  notified  by  VTT  (Finnish  Notified  Body, 

listed by EC) 

  = Certified for explosion hazardous areas 

II

   = Certified for use in areas excluding mines 

2  

= Equipment category (suitable for Zone 1 and Zone 2) 

G

   = Certification taking account explosion hazardous GASES 

Explanation of marking for explosion hazardous area due to Gases 

Ex 

= Certified for use in explosion hazardous areas 

e

   = Explosion protection method increased safety (of certain components) 

mb 

= Explosion protection method encapsulation (encapsulating ignition sources) 

op  is

 = Explosion protection method optically inherently safe (visible or infrared radiation that is 

incapable of producing sufficient energy under normal or specified fault conditions to ignite a 
specific  hazardous  athmosphetic  mixture).  This  definition  is  analogues  to  the  term 
“intrinsically safe” applied to electrical circuits 

IIC

  = Equipment group (including explosion hazardous areas of IIA, IIB and IIC gases) 

T4

   = Maximum temperature of the unit is 135°C (within the ambient temperature range of 

-20°C

+40°C) 

Gb

  =  Explosion  Protection  Level  (EPL)  marking  for  “HIGH”  level  of  protection.  Equipment  for 

explosive 

GAS

 atmospheres, which is not a source of ignition in normal operation or during 

expected malfunctions 

Summary of Contents for SLAM Star













Reviews: