manualshive.com logo in svg

ATEN VM51616H, User Manual

Share
Download
ATEN VM51616H User Manual Download Page 84

VM51616H User Manual

74

Maintenance

The 

Maintenance 

page lets users upgrade the VM51616H’s firmware and back 

up or restore system settings. This is an Administrator only function.

To upgrade the VM51616H’s firmware, do the following:

1. Use the 

Browse

 button to locate the firmware upgrade file. Make sure you 

have the correct file saved on your PC.

2. Click 

Upgrade 

to begin the upgrade procedure.

Note:

After updating the firmware, it’s recommended that you clear your web 
browser’s cache and then close and reopen the web browser. This will 
ensure the GUI refreshes and functions properly.

To back up the VM51616H’s system settings, do the following:

1. Click 

Backup

.

 

A configuration file will then begin downloading.

To restore the VM51616H’s system settings, do the following:

1. Use the 

Browse

 button to locate the configuration file. Make sure you 

have the correct file saved on your PC.

2. Click 

Restore 

to begin the restoration procedure.

Note:

User accounts cannot be backed up or restored.

Summary of Contents for VM51616H





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands