ATEN VM51616H User Manual Download Page 73

Page: 73 / 124

Chapter 4. Browser Operation

Network

The

Network

page

lets you configure the IP settings, website timeout, and

Telnet settings for connecting to the VM51616H.

Enable

DHCP to allow the DHCP server to assign an IP address to the

VM51616H. Select

Disable

to enter your own static IP address settings for the

device.

Click

Reset

to use the following default values:

IP Address – 192.168.0.60

Subnet Mask – 255.255.255.0

Default Gateway – 192.168.0.1

Website Timeout* – 5 minutes

Telnet Enabled

Enter the values, then click

Save

. Changes may take a few seconds and after

refreshing the page automatically redirects you to the IP address specified.

This option controls how long an inactive web connection stays logged
into the VM51616H. Use N/A to disable this option. Other options
include 5, 10, 30 and 60 minutes. Any changes will take effect
immediately.

Summary of Contents for VM51616H





























































































































Search results

Summary of Contents for VM51616H

Reviews:

Brands by name

Popular brands

ATEN VM51616H, User Manual

Search results

Summary of Contents for VM51616H

Reviews:

Brands by name

Popular brands