manualshive.com logo in svg

ATEN VM51616H, User Manual

Share
Download
ATEN VM51616H User Manual Download Page 44

VM51616H User Manual

34

Array Pushbutton

The 

ARRAY

 pushbutton allows users conveniently select the viewing mode 

and the input sources for the local display. Press the 

Array

 pushbutton to enter 

the setting page.

Š

Press the 

Prev

 or 

Next

 pushbutton to select a viewing mode for the display 

connected to the local HDMI Output Port. The available viewing modes 
are: Single (1x1), Side by Side (1x2), Quad View (2x2), and Show All 
(4x4).

Š

Use pushbuttons 

1-16

 to select the input sources to be shown on the local 

display. The selected sources will show on the display sequentially (from 
upper left to lower right).

Š

Press the 

Cancel

 pushbutton to reset the settings.

Š

Press the 

Array 

pushbutton to exit.

Note:

The resolution cannot be set with the Front Panel Operation (default 
resolution: 1920x1080@60HZ). Users can select the resolution using 
the Browser GUI. See

Local Output

, page 79.

Array Mode: Quad View
Selected Input(s):  --, --, --, --
Resolution: 1920x1080@60HZ
Mode:             |    Reset: Cancel     |     Exit: Array

Array Mode: Quad View
Selected Input(s):  8, 12, 9, 16
Resolution: 1920x1080@60HZ
Mode:             |    Reset: Cancel     |     Exit: Array

Array Mode: Quad View
Selected Input(s):  8, 12, 9, 16
Resolution: 1920x1080@60HZ
Mode:             |    Reset: Cancel     |     Exit: Array

Summary of Contents for VM51616H





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands