manualshive.com logo in svg

ATEN VM51616H, User Manual

Share
Download
ATEN VM51616H User Manual Download Page 19

Chapter 2. Hardware Setup

9

Cable Connection

Installation of the VM51616H is simply a matter of connecting the appropriate 
cables. Refer to the installation diagram on the following page (the numbers in 
the diagram correspond to the steps below), and do the following:

1. Use a grounding wire to ground the unit by connecting one end of the wire 

to the grounding terminal, and the other end of the wire to a suitable 
grounded object.

Note:

Do not omit this step. Proper grounding helps to prevent damage to 
the unit from surges or static electricity.

2. If using the Browser Operation features (see 

Browser Operation

, page 37), 

plug a Cat 5e cable from the LAN into the VM51616H’s 

Ethernet

 port.

3. If you are using the serial control function, use an appropriate RS-232 

serial cable to connect the computer or serial controller to the 
VM51616H’s female 

RS-232 Serial 

port.

4. Connect up to 16 HDMI video sources to the 

HDMI Input

 ports.

5. Connect up to 16 HDMI display devices to the 

HDMI Output

 ports. 

6. Plug the power cord supplied with the package into the VM51616H’s 3-

prong AC socket, and then into an AC power source. 

7. (Optional) Connect a display to the local HDMI output port to enable 

multi-view preview from the connected source device(s).

8. (Optional) Connect a speaker to extract HDMI audio.

9. Power on the VM51616H and all devices in the installation. 

Summary of Contents for VM51616H





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands