ATEN VM0808H User Manual Download Page 64

Page: 64 / 78

VM0808H User Manual

Power On Detection Commands

Enabling Power On Detection means that the VM0808H automatically
switches to the next powered on device when one of the HDMI source devices
is powered off.

The formula for Power On Detection commands is as follows:

Power On Det Control command [Enter]

For example, to turn on the Power On Detection feature, input the following:

pod on [Enter]

The following tables show the possible values for the Power on Detection
commands:

The following table shows the available command list:

Command

Description

pod

Power On Detection function

Control

Description

Enable power on detection
function

off

Disable power on detection
function (default)

Command

Control

Enter

Description

pod

[Enter]

Turn on power on detection

pod

off

[Enter]

Turn on power off detection (default)

Summary of Contents for VM0808H















































































Search results

Summary of Contents for VM0808H

Reviews:

Related manuals for VM0808H

Brands by name

Popular brands

ATEN VM0808H, User Manual

Search results

Summary of Contents for VM0808H

Reviews:

Related manuals for VM0808H

Brands by name

Popular brands