ATEN VM0808H User Manual Download Page 12

Page: 12 / 78

VM0808H User Manual

Features

Connects any of 8 HDMI sources to any of 8 HDMI displays

Long Distance Transmission - supports up to 20 meters (24 AWG HDMI
standard cable)

HDMI (3D, Deep Color) and HDCP compatible

Easily switch between multiple sources and multiple displays

Local Operation:

Front panel LCD display

Tuner Dials and Pushbuttons

IR Remote Control

Serial controller

Remote Operation:

Browser Graphical User Interface (GUI)

Superior video quality – HDTV resolution of 480p, 720p, 1080i, and
1080p (1920 x 1080); VGA, SVGA, SXGA, UXGA and WUXGA (1920 x
1200)

Supports Dolby True HD and DTS HD Master audio

Signaling rates up to 2.25 Gbits

Features EDID Expert technology:

EDID Library with 14 default EDID configurations

Built-in EDID Mode selection

Copies a display's EDID to selected source devices

Power on Detection - If an HDMI source is powered off, the VM0808H
can automatically switch to the next powered-on source

Firmware upgradeable

Rack Mountable

Note:

The VM0808H AP and GUI operation instructions can be downloaded
from the ATEN website (www.aten.com).

Summary of Contents for VM0808H















































































Search results

Summary of Contents for VM0808H

Reviews:

Related manuals for VM0808H

Brands by name

Popular brands

ATEN VM0808H, User Manual

Search results

Summary of Contents for VM0808H

Reviews:

Related manuals for VM0808H

Brands by name

Popular brands