3
ASSEMBLY
5HIHU
to
)LJXUH
1
1. Three ma
M
or parts should
EH
included in pa
FNDJH
D
+\GUDXOLF
unit with pumpi
QJ
mechanism
E
saddle unit
F
pieces of
E
ase half with
ERO
ts and washers
. Attach one of the
EDVH
halves to the
EDVH
of the
K\G
raulic unit, then secure usin
J
allen head
E
olts and
washers provided. Then
DSSO\
the same procedure to
the other
EDVH
half. Use torque wrench to
WLJKWHQ
to
30
IW
l
EV
. torque. Do not overt
LJ
hten.
3. Attach the
EUDFNH
ts to the reservoir, then attach one end
of the support
EDUV
to
E
ase half and the other end to the
EUDFNHW
. Secure with
ERO
ts and nuts provided.
5
epeat
for all other three support
E
ars.
4. Slide the position handle to the reservoir from top, then
secure with
EROWV
and nuts provided.
.
3RVLWLRQ
the saddle unit
DERYH
the ram piston, place
the saddle
VRFNHW
onto the ram piston. Secure usin
J
the set screw.
Raise Saddle:
1.
3
ump foot pedal or press air pump pedal until
saddle reaches desired position.
.
)ROORZ
vehicle manufact
XUHU¶V
recommended
procedures for r
HPRYLQJ
the load as outlined in vehicle
service manual or repair
JXLGH
.
3. Secure load with provided chains.
4.
(QVXUH
ORDG
s center of
JUD
vi
W\
is centered on the saddle
and load is st
DEOH
EHIRUH
movi
QJ
MDFN
Lower Saddle:
CAUTION!
%H
sure all tools and personnel are clear
E
efore
loweri
QJ
load.
Slowl
\
,
J
e
QWO\
DSSO\
downward pressure to the release valve
pedal.
To avoid crushing and related
injuries:
NEVER work on, under or
around a load supported only
by a jack. Immediately
transfer the load to an
appropriate work station.
!
WARNING
BEFORE USE
1. Inspect
MDFN
EHIRUH
each use. Do not use if
EHQW
EURNH
n
or crac
NH
d components are noted.
(
nsure that casters
move freel
\
. Chec
N
for and
WLJ
hten
DQ\
loose
DVVHPEOL
es.
. Verif
\
that the product and the application are compati
E
le.
:LWKUDPIXOO\ORZHUHGUHPRYHRLOILOOHUVFUHZWREOHHG
air in the reservoir.
4.
(Q
sure oil level is
M
ust
EH
low the rim of the oil filler screw
hole.
5HLQV
tall the oil filler screw
Study, understand, and follow all printed materials
provided with/on this product before use.
Do not exceed rated capacity.
Use only on hard, level surfaces capable of
supporting rated capacity loads.
Use of this jack is limited to the removal, installation
and transportation of transmissions, transfer cases
and transaxles. Do not use a transmission jack to
tilt or support a vehicle.
Ensure the center gravity of load is centered on the
saddle.
Do not exceed 10˚ tilt angle of the saddle assembly
in all directions.
Adequately support the vehicle before starting repairs.
Use only chains and slings provided.
If loaded jack must be moved, make sure that the
load is secured, stable and in lowest position.
This is a lifting and lowering device only.
Transfer load immediately to appropriate support
device for service or repair.
No alterations shall be made to this product
Failure to heed these markings may result in
personal injury and/or property damage.
!
WARNING