manualshive.com logo in svg

AT&T SPIRIT 308, Administration Manual

Share
Download
AT&T SPIRIT 308 Administration Manual Download Page 14

Customizing the System

■ 

PBX/CENTREX LINE ACCESS CODES

■

Press FEATURE. Dial 5.
All of the line indicator lights will go off.

To ENTER a system-wide PBX/Centrex dial code.
Dial the desired dial code. Press ADD button. You will hear the confirmation tone when
the code is added. If there are already four other codes programmed you will hear the error
tone. The digit 9 is preset as the PBX/Centrex code, so there is room for three other codes. You
may, of course, erase the 9 code if you wish.

To ERASE a system-wide PBX/Centrex dial code.
Dial the code you wish to erase. Press DROP. You will hear the confirmation tone when

the code is erased. If the code is not there to be erased, you will hear the error tone.

To ERASE all codes.

Press DROP. Dial *. Press DROP. You will hear the confirmation tone if you successfully

followed the DROP procedure.

You may continue to enter or erase codes or you may exit the feature.

EXTERNAL ALERT
Press FEATURE. Dial 6.
Each line indicator light will show the current external alert status for that line. To make
changes, press the line button(s) for the line(s) on which you wish to make a particular
change and dial one of the digits from the table below. You may press more than one line
button to make the change on more than one line. If you enter a digit without first pressing
a line button you will hear the error tone.

DIAL

INDICATOR LIGHT

SETTING

1

OFF

Never use external alert

2

ON

External alert when Night Service is on (installed)

3

Even Flash

External alert when Night Service is off

4

“Wink” (Short ON, Long OFF)

External alert always on

■ 

DIAL TYPE
Press FEATURE. Dial 7.

Each line indicator light will show the current dialing type for that line. If the light is OFF,
that line is set for touch tone dialing. If the light is ON, the line is set for dial pulse
dialing. To change the dialing type for a line or lines, press the line button(s) and dial the
appropriate digit from the table below. Y

OU 

may press more than one line button to make

the change on more than one line. If you enter a digit without first pressing a line button
you will hear the error tone.

DIAL

INDICATOR LIGHT

SETTING

1

OFF

Touch Tone

2

ON

Dial Pulse (installed)

Administration Manual 13

Summary of Contents for SPIRIT 308


































Reviews:

No comments

Brands by name

Popular brands

Load more brands