AT&T OneVision DEFINITY G3 Guide Installation And Connection Manual Download

Page: 98 / 287

5-20

Issue 2 April 1996

Planning Connectivity
Cables for Data Modules

Cables for Data Modules

Type of PBX

The type of PBX you have does not affect the cabling.

Data module
cables

The following diagram shows the cabling for a configuration that
includes a 7400B data module.

Legend

1. PBX

2. Digital-line circuit pack on PBX

3. B25A cable

4. Cross connection at main distribution frame

5. 103A or wall jack

6. D8W-87 cable

7. 7400B data module

8. M25A cable

9. Proxy Agent PC

10. 5000 feet maximum between the PBX and data module

Summary of Contents for OneVision DEFINITY G3 Guide
































































































































































































































































































Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

Related manuals for OneVision DEFINITY G3 Guide

Brands by name

Popular brands

AT&T OneVision DEFINITY G3 Guide, Installation And Connection Manual

Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

Related manuals for OneVision DEFINITY G3 Guide

Brands by name

Popular brands