AT&T OneVision DEFINITY G3 Guide Installation And Connection Manual Download

Page: 110 / 287

5-32

Issue 2 April 1996

Planning Connectivity
To Set the Dip Switch

Settings for
a MPDM

The following table shows the settings for the dip switches on a
MPDM.

The dip switch must be set at this option.

Settings for
an ADU

If you are using an ADU, the ADU must be supplied with external
power.

Dip switch

Setting

Dip switch

Setting

LOW

OFF

SYNC

ASYN

300

OFF

INT

EXT

1200

OFF

DISC

OFF

2400

OFF

KYBD

OFF

4800

OFF

PRTY

OFF

9600

I/OD

OEN

19.2

OFF

DMLL

OFF

56K

OFF

MKBY

OFF

64K

OFF

SPARE

(none)

TRDK

OFF

SIGLS

OFF

HDX FDX

AANS

OFF

Summary of Contents for OneVision DEFINITY G3 Guide
































































































































































































































































































Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

Related manuals for OneVision DEFINITY G3 Guide

Brands by name

Popular brands

AT&T OneVision DEFINITY G3 Guide, Installation And Connection Manual

Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

Related manuals for OneVision DEFINITY G3 Guide

Brands by name

Popular brands