AT&T 2634DA Service Manual Download Page 1

BELL  SYSTEM  PRACTICES 
AT&TCo  Standard 

SECTION  502-612-409 
Issue  4,  October  1975 

SERVICE 

2634DA,  2634DAM,  2635DA,  AND  2635DAM  TELEPHONE  SETS 

1.  GENERAL 

1.01 

This section conta.ins connection and maintenance 
information  for  2634DA  or  DAM  (18-button) 

and 2635DA or DAM (30-button) CALL DIRECTOR® 
telephone  sets. 

1.02 

This  section  is  reissued  to: 

• 

Add  information  on  2634DAM  and  2635DAM 
(modular)  telephone  sets. 

• 

Add  comcode  numbers. 

1.03 

•Current  nonmodular  2634DA  and  2635DA 

telephone sets are furnished from  the factory 

equipped  with  a  G3A6  handset  and  cord.  Modular 

2634DAM and 2635DAM telephone sets are equipped 
with  a  G15A  handset  H4DU  handset  cord,  and  616E 

jack assembly (Fig.  1) .• 

2. 

CONNECTIONS 

2.01 

These  sets  are  factory-wired  for  use  with 

1A1, 1A2, or 6A KTS station line concentrators. 

Refer  to  Division  518  for  connections  using  235-
or  236-type  key telephone units. 

2.02 

A  235-type  KTU  is  associated  with  each 

2634-type  telephone  set  and  a  236-type  KTU 

with  each  2635-type  telephone  set.  Because  of 
the  single  common talking  and  control  lead  pattern 
in  these  sets,  a  line  concentrator  KTU  must  be 

associated  with  each  telephone  set  installed  and 

cannot be  shared,  even  on  a  bridged station basis. 

2.03 

The  2634DA  or  DAM  and  2635DA  or  DAM 

sets  are  equipped  with  a  635A5C  key  (5-line 

pickup  and  hold)  key  in  the  first  module  position. 

This  may  be  replaced  with  a  635AD5C  (4-line 

pickup,  cutoff,  and  hold)  key.  Contact  strip 
assemblies  differ  between  the  two  keys.  If  ordered 
for  field  replacement,  the  635AD5C  is  furnished 
with  a  piggy-back  adapter,  in  the  cut  off  key 

position,  for  storing  the  slate  mounting  cord  plug 

associated  with  the  fifth  line.  The  necessary  contact 

strip  assemblies  (840151039  and  840151047)  will  be 

shipped  with  the  635AD5C  and  will  replace  the 

840151120  and  840151138  assemblies  supplied  with 
the  635A5C  key. 

2.04 

Because  of  the  physical  arrangement  of  the 

635-type key,  the contact strips do not  extend 

to  the  chaining  switch.  This  requires  additional 
A1  leads  to  each module (except the last),  to  extend 
A  lead  control. 

2.05 

Mounting  cords  of  these  CALL  DIRECTOR 

sets  terminate  in  individual  plugs  connected 

to the  rear of  the keys.  This  permits rearrangement 
of  line  appearances  either  in  the  set  or  at  the  key 
equipment  distribution  point.  Current  production 
sets  are equipped with  a satin-silver ( -87) mounting 
cord. 

2.06 

All  line  key  positions  are  convertible  from 

pickup  (locking)  to  signaling  (nonlocking). 

To  convert  a  key  position  to  signaling,  remove  the 
•812857738  or•  P-28E773 screw  detail from  the  key 
position  involved  and  place  840157671  insulating 
details  over  the  two  key  contacts  adjacent  to  the 
plunger  (refer  to  Section  512-230-101).  Make 
necessary  wiring  changes  as  shown  in  Table  A  for 

2634DA  or  DAM  and  Table  B  for  2635DA  or  DAM. 

Note: 

If  more  than  six  signaling  keys  are 

required,  replace  635G5C  key  in  last  module 
with  a  658A  key. 

2.07 

The  2634DA  or  DAM  and  2635DA  or  DAM 
telephone  sets  are  factory  equipped  with  a 

KS-20419L1  (10  volt  ac  only)  buzzer. 

2.08 

For  3-type  speakerphone  operation,  a  679A 

transmitter  may  be  installed  in  3rd  (2634DA 

or  DAM)  or  5th  (2635DA  or  DAM)  module.  For 
necessary wiring changes and connections,  see Table 
C  and  Fig.  4. 

NOTICE 

Not  for  use  or disclosure  outside  the 

Bell  System  except  under  written  agreement 

Printed 

in 

U.S.A. 

Page  1 

BSP 502-612-409-i04_1975-10-0l.jpg  Scanned by  Frank  Harrell, (Cowboy  Frank) Castle Rock, Colorado  Feb 04, 2012 

Summary of Contents for 2634DA
















Reviews: