Asus RS720-E7-RS24-EG User Manual Download Page 116

Page: 116 / 202

5-40

Chapter 5: BIOS setup

Setup Prompt Timeout [xx]

Use the <+> and <-> keys to adjust the number of seconds to wait for setup activation key.

Bootup NumLock State [On]

Allows you to select the power-on state for the NumLock.

Configuration options: [Off] [On]

Full Screen Logo [Enabled]

Allows you to enable or disable the full screen logo display feature.

Configuration options: [Disabled] [Enabled]

Set this item to [Enabled] to use the ASUS MyLogo2™ feature.

GateA20 Active [Upon Request]

This item is useful when any RT code is execute above 1MB. When set to [Upon Request],

the GA20 can be disabled using BIOS services. When set to [Always], disabling of GA20 is

not allowed. Configuration options: [Upon Request] [Always].

Option ROM Messages [Force BIOS]

Allows you to set the display mode for Option ROM. Configuration options:
[Force BIOS] [Keep Current]

INT19 Trap Response [Immediate]

This item allows you to set the BIOS reaction on INT19 trapping by Option ROM.

Configuration options: [Immediate] [Postponed]

5.7

Boot menu

The Boot menu items allow you to change the system boot options.

Summary of Contents for RS720-E7-RS24-EG











































































































































































































Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Brands by name

Popular brands

Asus RS720-E7-RS24-EG, User Manual

Search results

Summary of Contents for RS720-E7-RS24-EG

Reviews:

Brands by name

Popular brands